Important Points to Remember, Kickback occurs

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

IGNITION

SWITCH

STOP

Choke

Lever

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

OFF

HALF

FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 30 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.To set the fast idle, pull the choke/fast idle lever out to the full extent (to the full choke position); then push the lever back in to the HALF CHOKE position.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position. Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

545186805 specifications

The Poulan 545186805 is an impressive chainsaw designed to meet the demands of both the seasoned professional and the enthusiastic DIYer. This chainsaw combines robust performance with user-friendly features, making it a popular choice among users looking for reliability and efficiency.

One of the key characteristics of the Poulan 545186805 is its powerful engine. Equipped with a 50cc two-stroke engine, it delivers impressive cutting power that allows users to tackle large logs and tough tree trunks with ease. This engine is designed for optimal performance, offering a balance of power and fuel efficiency, ensuring that users can work longer without frequently stopping to refuel.

In addition to its potent engine, the Poulan 545186805 features a 20-inch guide bar, allowing for deeper cuts and the ability to handle larger wood types. This extended reach is particularly beneficial for users who need to fell trees or cut through thicker branches, adding versatility to its applications.

Safety is an important factor for chainsaw users, and the Poulan 545186805 incorporates several safety features designed to protect users. It has an automatic chain oiler which achieves continuous lubrication, reducing wear on the chain and the bar, thereby enhancing longevity. Additionally, it comes equipped with a chain brake that reduces the risk of kickback, ensuring safer operation.

The design of the Poulan 545186805 emphasizes comfort and ease of use. It features an ergonomic handle that provides a secure grip, reducing fatigue during extended use. The lightweight construction further enhances maneuverability, making it easier to handle for extended periods, which is especially important for those undertaking larger projects.

Moreover, the Poulan 545186805 integrates advanced technology to ensure a smoother operation. The Easy Start feature allows users to start the engine with minimal effort, preventing frustration and providing a user-friendly experience, particularly for those who may not be accustomed to handling chainsaws.

In summary, the Poulan 545186805 is a versatile and powerful chainsaw that stands out with its combination of performance, safety, and user-friendly features. Whether for professional use or home projects, this chainsaw can effectively meet the needs of a variety of users, making it a solid choice for anyone in need of a reliable cutting tool.

Poulan 545186805 Important Points to Remember, Starting a Warm Engine, Kickback occurs

Models: 545186805