TROUBLESHOOTING

 

PROBLEM

CAUSE

CORRECTION

 

Engine continues

1.

Faulty operator-safety presence control

1.

Check wiring, switches and connections. If not

 

to run when oper-

 

system.

 

corrected, contact an authorized service center/

 

ator leaves seat

 

 

 

department.

 

 

 

 

 

 

 

with attachment

 

 

 

 

 

 

clutch engaged

 

 

 

 

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

 

 

2.

Mower deck not level.

2.

Level mower deck.

 

 

3.

Buildup of grass, leaves, trash under mower.

3.

Clean underside of mower housing.

 

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

 

5.

Clogged mower deck vent holes from

5.

Clean around mandrels to open vent holes.

 

 

 

buildup of grass, leaves, and trash around

 

 

 

 

 

 

mandrels.

 

 

 

 

Mower blades will

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

 

 

not rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

 

 

 

Poor grass

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

 

discharge

2.

Travel speed too fast.

2.

Shift to slower speed.

 

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

 

4.

Mower deck not level.

4.

Level mower deck.

 

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

 

6.

Worn, bent or loose blade.

6.

Replace blade. Tighten blade bolt.

 

 

7.

Buildup of grass, leaves, trash under mower.

7.

Clean underside of mower housing.

 

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

 

10.

Improper blades used.

10.

Replace with blades listed in parts manual.

 

 

11.

Clogged mower deck vent holes from buildup

11.

Clean around mandrels to open vent holes.

 

 

 

of grass, leaves, trash around mandrels.

 

 

 

 

Headlight(s) not

1.

Switch is “OFF”.

1.

Turn switch “ON”.

 

 

working

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

(if so equipped)

3.

Faulty light switch.

3.

Check/replace light switch.

 

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

 

 

 

Battery will not

1.

Bad battery cell(s).

1.

Replace battery.

 

 

charge

2.

Poor cable connections.

2.

Check/clean all connections.

 

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

 

2.

Debris on steering plate (if equipped).

2.

See "CLEANING" in the maintenance section.

 

 

3.

Motion drive belt worn, damaged, or broken.

3.

Replace motion drive belt.

 

 

4.

Air trapped in transmission during

4.

Purge transmission.

 

 

 

shipment or servicing.

 

 

 

 

 

5.

Axle key missing.

5.

Install axle key at rear wheel. See "TO REMOVE

 

 

 

 

 

WHEEL" in the Service and Adjustments section.

 

 

 

 

 

 

 

 

Engine "back-

1.

Engine throttle control not set between

1.

Move throttle control between half and full speed

 

 

fires” when turn-

 

half and full speed (fast) position before

 

(fast) position before stopping engine.

 

 

stopping engine.

 

 

 

 

ing engine “OFF”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Engine dies when

1.

Reverse operation system (ROS) is not "ON"

1.

Turn ignition key to ROS "ON" position. See

 

 

tractor is shifted

 

while mower or other attachment is engaged.

 

Operation section.

 

into reverse

 

 

 

 

 

 

 

 

 

 

 

 

27

Page 27
Image 27
Poulan 96042012600 Engine continues, To run when oper, Ator leaves seat, With attachment Clutch engaged Poor cut uneven

96042012600, 85-50 specifications

The Poulan 96042012600, often referred to as the 85-50, is a powerful and versatile chainsaw designed to meet the needs of both professionals and avid DIYers. Renowned for its performance and reliability, the 85-50 is suitable for a wide range of cutting tasks, including tree felling, pruning, and firewood preparation.

One of the standout features of the Poulan 85-50 is its robust engine. Powered by a 50cc two-stroke engine, it delivers impressive cutting power while maintaining a relatively lightweight design. This balance between power and weight translates into ease of use, allowing users to operate the chainsaw for extended periods without excessive fatigue. The engine is engineered for efficient fuel usage, contributing to reduced emissions and making it an environmentally friendly choice.

The chainsaw features a 20-inch bar and chain, providing a significant cutting capacity ideal for tackling both small and large trees. The longer bar allows for deeper cuts, making it easier to handle more substantial timber. Additionally, the chain is designed for high performance, ensuring smooth and efficient cuts.

Another key technology in the Poulan 85-50 is its automatic oiler system, which delivers a consistent flow of chain oil to keep the bar and chain lubricated during operation. This feature not only enhances the cutting efficiency but also prolongs the lifespan of the chainsaw by reducing wear and tear on the chain and bar.

Safety is a priority with the Poulan 85-50, which is equipped with a chain brake that can instantly stop the chain in the event of kickback. The design also includes a throttle lock, preventing accidental acceleration and ensuring safe operation. Its anti-vibration technology further reduces operator fatigue, allowing for more control and precision while cutting.

Ergonomics play a significant role in the design of the Poulan 96042012600. The handle is designed to provide a comfortable grip, allowing for better maneuverability, whether you're cutting at ground level or overhead. Additionally, the chainsaw features an easily accessible air filter, simplifying maintenance and ensuring the machine operates at peak efficiency.

In conclusion, the Poulan 96042012600, 85-50, stands out for its combination of power, efficiency, and safety features. With its lightweight design, advanced technology, and ergonomic considerations, it is an excellent choice for anyone seeking a reliable chainsaw for various cutting tasks, making it a valuable tool for both residential and professional use.