REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001900)
AUGER HOUSING / IMPELLER ASSEMBLY
KEY | PART |
| KEY | PART |
|
|
NO. | NO. | DESCRIPTION | NO. | NO. | DESCRIPTION |
|
1 | 182516 | Bar, Weight | 29 | 174762X479 | Skid Plate, LH |
|
2 | 751153 | Nut, Hex, Flangelock | 30 | 405973X479 | Auger Assembly, RH | |
3 | 72110510 | Bolt, Carriage | 31 | 405972X479 | Auger Assembly, LH | |
4 | 191079 | Pulley, Impeller | 32 | 407768 |
| |
5 | 188909 | Bearing Assembly, Flange | 33 | 407769 | Bushing, Flange 3/4 | |
6 | 155377 | Nut, Hex Flange | 34 | 174681 | Washer, Thrust 3/4 | |
7 | 180355 | Bolt, Flat Head, Carriage | 35 | 174684 | Bearing, Thrust | 3/4 |
|
| 36 | 407757 | Shaft, Impeller |
| |
8 | 72270505 | Bolt, Carriage | 37 | 174683 | Washer, Thrust | 5/8 |
9 | 163183 | Bolt, Hex Head | 38 | 407758 | Bushing, Flange 5/8 | |
10 | 404930X428 | Housing, Auger | 39 | 407767 | Screw, Hex Head | |
11 | 404933X479 | Bar, Scraper | 40 | 407760 | Plug, Case |
|
12 | 178675X008 | Bracket, Corner Discharge | 41 | 407761 | Housing, Gearbox, RH | |
13 | 175322 | Base, Discharge Chute | 42 | 407770 | Seal, Oil |
|
14 | 10040500 | Washer, Lock 5/16 | 43 | 407762 | Bushing, Flange, 1" | |
15 | 19111507 | Washer, Flat | 44 | 189282 | Key, Square 1/4 x 1/4 x 7/8 | |
16 | 74940516 | Screw, Hex Head | 45 | 407763 | Gear, Worm |
|
17 | 405637 | Grease Fitting | 46 | 407764 | Shaft, Auger |
|
18 | 179582 | Screw, Hex Head 5/16 x 1 | 47 | 407765 | Housing, Gearbox, LH | |
19 | 73800400 | Nut, Hex Lock | 48 | 175321X428 | Impeller Assembly | |
20 | 155377 | Nut, Hex Lock | 49 | 74780426 | Screw, Hex Head | |
21 | 401347 | Washer, Flat | 50 | 407766 | Gasket, Gearbox | |
22 | 178777X479 | Skid Plate, RH | 51 | 7836M | Pin, Roll 3/16 x | |
24 | 128638 | Wing Nut | 52 | 181160X479 | Bar, Drift Cutter |
|
25 | 72270506 | Bolt, Carriage | 54 | 198709 | Stop |
|
26 | 174658 | Bearing, Auger | 55 | 198638 | Spacer |
|
27 | 174697 | Washer, Thrust, 1" | 56 | 180684 |
| |
28 | 198636 | Bolt, Shear | 57 | 196710 | Gearbox Assembly | |
|
|
| 58 | 411939 | Plug, Bearing Hole |
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
21