|
|
| OPERATION |
| |||
SPARK |
|
| ENGINE OIL CAP | AUGER | DISCHARGE CHUTE CONTROL LEVER | ||
PLUG |
|
| WITH DIPSTICK | CONTROL |
|
| |
SAFETY |
|
|
|
| LEVER | DRIVE SPEED | DEFLECTOR REMOTE |
IGNITION |
|
|
|
|
| CONTROL LEVER | |
|
|
|
|
| CONTROL LEVER | ||
KEY |
|
|
| GASOLINE |
|
| |
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
| FILLER |
|
|
|
|
|
|
| CAP |
|
| TRACTION |
CHOKE |
|
|
|
| CHUTE |
| |
|
|
|
|
| DRIVE | ||
|
|
| DEFLECTOR |
| |||
CON- |
|
|
|
| CONTROL | ||
|
|
|
|
|
| ||
TROL |
|
|
|
|
|
| LEVER |
|
|
| OIL |
|
|
|
|
|
|
| DRAIN |
|
| LH TURN | |
|
|
| PLUG |
|
|
| |
THROTTLE |
|
|
|
|
|
| TRIGGER |
/ ENGINE |
|
|
|
|
|
|
|
CONTROL |
|
|
|
|
|
|
|
|
|
| DISCHARGE |
|
|
| |
|
|
|
| CHUTE |
|
|
|
RECOIL | POWER |
|
|
|
|
|
|
(AUXILIARY) |
|
|
|
|
|
| |
CORD |
|
|
|
|
|
| |
STARTER |
|
|
|
|
| LIGHT | |
PLUG | ELECTRIC |
|
|
|
| ||
HANDLE |
|
|
|
|
|
| |
|
| START | FUEL |
|
|
|
|
|
| BUTTON | CLEAN- |
|
|
| |
PRIMER |
|
|
|
| HANDLE | ||
|
| VALVE | OUT |
|
| ||
|
|
|
| TOOL |
|
| KNOB |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| MUFFLER |
NOTE: ITEMS ABOVE |
|
ARE SHOWN IN |
|
THEIR TYPICAL | TOOLBOX |
LOCATION ON THE |
|
ENGINE. ACTUAL |
|
LOCATION MAY VARY |
|
WITH THE ENGINE |
|
ON YOUR UNIT. |
|
DRIFT CUTTER
SKID PLATE
AUGERS
FIG. 10
MEETS A.N.S.I. SAFETY REQUIREMENTS
Our snow throwers conform to the standards of the American National Standards Institute.
Toolbox - used to store spare shear bolts, locknuts and wrench.
Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.
Electric start button - used for starting the engine.
Recoil (auxiliary) starter handle - used for starting engine.
Drift cutter - used to cut through deep snowdrifts.
Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.
Choke control - used for starting a cold engine.
LH and RH turn triggers - used to steer the snow thrower.
Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.
Traction drive control lever - used to engage
Auger control lever - used to engage auger motion (throw snow).
Discharge chute control lever - used to change the di- rection the snow is thrown.
Skid plate - used to adjust height of scraper bar from the ground.
Deflector remote control lever - used to change the
9 distance the snow is thrown.
