Gearbox Assembly, Bearing, Impeller Pulley, Plug | Poulan 421474

REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001903)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART
NO.	NO.	DESCRIPTION

1175321X479 IMPELLER

2196710 GEARBOX ASSEMBLY

3	188909	BEARING
4	191079	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4−20
10	74780426	SCREW 1/4−20 X .625
11	155377	NUT 5/16−18

12163183 SCREW 5/16−18 X .625

1319111507 WASHER

1410040500 LOCKWASHER 5/16

1574940516 SCREW 5/16−18 X 1.00

16180355 CARRIAGE BOLT

17194189 SCREW 13−16 X .625

18	407760	PLUG
19	407761	GEARBOX COVER RH
20	407766	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	407757	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O−RING

35407767 SCREW 5/16−18 X .750

36407765 GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

23

Image 23

Poulan 421474 Gearbox Assembly, Bearing, Impeller Pulley, Discharge Base, 178675X008 Corner Bracket Clean OUT Tool, Plug

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Check Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Drive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting engine Stopping HOW to USE Your Snow Thrower To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See Fig ADD Gasoline See Fig Before Starting the EngineScraper BAR Check Engine OIL Level See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Maintenance Engine Cleaning Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Remove the klik pin and remove wheel from axle To Remove Wheels See Fig Other Storage Troubleshooting Auger Bearing Auger HousingKEY Part Description Scrapper BAR Skid Plate RH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate LH Exploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Bearing Plastic Washer Weight BAR181160X479 Drift Cutter BAR Deflector Seal Deflector Control AssemblyChute Weldment Deflector Weldment KEY Part Repair Parts Snow Thrower Model PP11530ES Handles Pivot Support Weldment Loop Handle LHLoop Handle RH Lower Handle Washer 3/8 SpacerKnob RED Handle Knob Carriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Sprocket Repair Parts Snow Thrower Model PP11530ES DriveAxle Shaft Item 43 Exploded Bottom PAN Speed Selector AssemblyDrive Plate Assembly END Plate Engine Mount Plate ENGINE, TECFrame Impeller Belt Belt CoverTraction Belt Cable Bracket RH Repair Parts Snow Thrower Model PP11530ES WheelsWheel Assembly LH Cable Bracket LH Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe 35062 Repair Parts Snow Thrower Model PP11530ES BAG of PartsSafety Ignition KEY 421474 421475 Repair Parts Snow Thrower Model PP11530ES Decals Limited Warranty