IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

02614

Weak or Dead

Fully Charged

Battery

Battery

REPLACING BATTERY

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Remove terminal guard.

3.Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

4.Install new battery with terminals in same position as old battery.

5.Reinstall terminal guard.

6.First connect RED battery cable to posi- tive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

7.Connect BLACK grounding cable to neg- ative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

8.Close terminal access doors.

9.Close hood.

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

Hood

Headlight Wire

Connector

02141

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, see engine manual

Terminal

Access

Door

Keps Nut

Hex Bolt

Positive (Red)

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be nec- essary. However, minor adjustment may be required to compensate for differences

Terminal Guard

Cable

Negative (Black) Cable

in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

24

Page 24
Image 24
Poulan CO185H42STC manual To Adjust Carburetor

CO185H42STC specifications

The Poulan CO185H42STC is a robust and versatile lawn tractor that has become a favored choice for homeowners seeking an efficient and reliable grass-cutting machine. With its powerful engine and efficient design, the CO185H42STC is equipped to handle both small and large lawns with ease.

One of the standout features of the Poulan CO185H42STC is its reliable engine. Powered by an 18.5 horsepower Briggs & Stratton engine, this lawn tractor is built for performance. The engine design ensures optimal power delivery, allowing for smooth operation while navigating various terrains. The automatic choke system further enhances user convenience, ensuring that the lawn tractor starts easily in all weather conditions.

The cutting deck of the CO185H42STC spans an impressive 42 inches, which allows users to cover large areas in a shorter amount of time. The deck is constructed using durable materials that can withstand wear and tear, ensuring longevity. The tractor also features an adjustable cutting height, offering six different positions between 1.5 inches to 4 inches, providing flexibility to achieve the desired lawn finish.

A notable technology included in this model is the hydrostatic transmission system. Unlike the traditional gear system, this advanced transmission allows for smooth speed changes without the need for gear shifting, enabling a more enjoyable driving experience. This feature is especially beneficial when navigating around obstacles or when mowing uneven terrain.

Comfort is another key aspect of the Poulan CO185H42STC. The tractor is equipped with a high-back seat that provides excellent support during extended mowing sessions. The ergonomic steering wheel maximizes maneuverability and is designed to minimize operator fatigue, ensuring a comfortable ride.

The CO185H42STC also includes a convenient bagging attachment, which allows for easy collection of clippings, making yard cleanup quick and efficient. Additionally, its rugged construction means it can handle challenging mowing tasks without the risk of damage.

In summary, the Poulan CO185H42STC is a highly capable lawn tractor that combines power, technology, and user-friendly features. Ideal for homeowners looking to maintain a pristine lawn, it stands out with its powerful engine, adjustable cutting deck, hydrostatic transmission, and focus on operator comfort. This lawn tractor offers a perfect blend of performance and convenience, making it a noteworthy addition to any lawn care toolkit.