SERVICE AND ADJUSTMENTS

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

• Block up axle securely.

• Remove axle cover, retaining ring and washers to allow

wheel removal (rear wheel contains a square key - Do

not lose).

• Repair tire and reassemble.

• On rear wheels only: align grooves in rear wheel hub

and axle. Insert square key.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

•

Replace washers and snap retaining ring securely in

 

axle groove.

•

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

22

FIG. 23

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

Page 21 Page 23
Page 22
Image 22
Poulan HD1842 manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER, Replacing Battery See Figs
Page 21 Page 23

HD1842 specifications

The Poulan HD1842 is a robust and reliable riding lawn mower designed for homeowners who require efficiency and ease of use while maintaining their lawns. This machine features a powerful engine paired with a 42-inch cutting deck, making it an ideal choice for medium to large-sized yards.

At the heart of the Poulan HD1842 is a reliable 18.5 HP Briggs & Stratton engine, known for its durability and performance. This engine provides ample power to tackle even the toughest grass, ensuring a smooth and effective cutting experience. The engine is designed for easy starting and requires minimal maintenance, making it suitable for users looking for convenience.

One of the standout features of the HD1842 is its cutting deck. The 42-inch deck is equipped with three high-performance blades that provide a clean and even cut, allowing for professional-looking results every time. The deck height can be easily adjusted to six different positions, ranging from 1.5 to 4 inches, giving users the flexibility to choose the perfect height for their grass type and desired look.

Another significant technology integrated into the Poulan HD1842 is the hydrostatic transmission. This feature allows for smooth and effortless speed adjustments while maintaining full control over the mower's movement. Users can easily navigate around obstacles and tight corners without the need to pause and change gears, enhancing the overall mowing experience.

Comfort is also a priority with the HD1842. The mower features a spacious and comfortable seat that can be adjusted to accommodate different user heights. Additionally, the steering wheel is ergonomically designed, providing a better grip and reducing operator fatigue even during extended mowing sessions.

For added convenience, the Poulan HD1842 comes equipped with an easy-access fuel tank that allows for quick refueling. The mower also features a built-in mulch kit and rear bagger options, making it versatile for different lawn care needs.

In summary, the Poulan HD1842 stands out for its powerful Briggs & Stratton engine, efficient 42-inch cutting deck, advanced hydrostatic transmission, and user-friendly features. This riding lawn mower is designed not only to get the job done efficiently but also to provide comfort and ease of use, making it a fantastic choice for any homeowner looking to maintain a pristine lawn.
Top Page Image Contents