BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel handling information in the safety rules sec- tion of this manual before you begin. If you do not understand the fuel handling information do not attempt to fuel your unit. Seek help from someone that does understand the in- formation or call the customer assistance help line at 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air- cooled engine oil designed to be mixed at a ra- tio of 40:1. Poulan/WEED EATER brand syn- thetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce (95 ml) container of Poulan/WEED EATER brand syn- thetic oil. Pour the entire contents of this con- tainer into 1 gallon (4 liters) of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan bar and chain oil is recom- mended to protect your unit against excessive wear from heat and friction. Poulan oil resists high temperature thinning.

If Poulan bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri- cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or meth- anol) can attract moisture which leads to sepa- ration and formation of acids during storage.

Acidic gas can damage the fuel system of an engine while in storage. To avoid engine prob- lems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible. The chain brake must be disengaged before cutting with the saw.

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15″ -- 18″ (40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

9

Page 8 Page 10
Page 9
Image 9
Poulan P4018WTL Before Starting Engine Fueling Engine, BAR and Chain Lubrication, Important Points to Remember
Page 8 Page 10

P4018WTL specifications

The Poulan P4018WTL is a robust and reliable chainsaw designed for homeowners and outdoor enthusiasts alike. This powerful tool is engineered to tackle a variety of cutting tasks, from pruning branches to felling trees, making it an essential addition to any toolkit.

One of the standout features of the Poulan P4018WTL is its 40cc 2-cycle engine. This engine delivers strong power while maintaining a compact design, allowing for ease of use and maneuverability. With a maximum power output of 2.3 horsepower, this chainsaw ensures efficient cutting through even tougher materials. It is equipped with a 18-inch cut chain, providing a great balance of length and control for various cutting jobs.

The chainsaw utilizes an innovative Air Injection technology, which helps in keeping the air filter clean by utilizing centrifugal force to remove larger debris before they reach the filter. This means less maintenance and longer intervals between filter cleaning, allowing users to focus on their cutting tasks rather than upkeep.

The Poulan P4018WTL also features an automatic oiler system, ensuring that the chain and bar receive consistent lubrication during operation. This self-lubrication helps to minimize friction, promoting a longer lifespan for both the chain and the bar while enhancing cutting efficiency.

Safety is a key consideration in the design of the P4018WTL. The chainsaw is equipped with a chain brake that stops the chain immediately in the event of kickback, preventing accidents and ensuring safety during use. Additionally, the ergonomically designed handle provides a comfortable grip and reduces fatigue, making it easier to handle the chainsaw during extended use.

With a lightweight construction of approximately 10.6 pounds, the Poulan P4018WTL is easy to carry and maneuver, providing both power and portability. Furthermore, it is designed with reduced vibration technology, which minimizes user fatigue and enhances comfort during operation.

In conclusion, the Poulan P4018WTL chainsaw combines power, features, and safety to meet the demands of various cutting tasks. With its efficient engine, innovative technologies, and user-friendly design, it stands out as a reliable choice for both novice and experienced users looking to tackle their landscaping and woodcutting needs.
Top Page Image Contents