Tractor

MAINTENANCE

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent ﬂat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without ﬁrst setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 12)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and ﬂat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and ﬂat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

	TRAILING	MANDREL
	TRAILING	ASSEMBLY
	EDGE UP	ASSEMBLY
	BLADE
		CENTER
		HOLE
	FLAT WASHER
	LOCK WASHER	STAR
		STAR

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a ﬁle or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

	CENTER HOLE
5/8" BOLT	BLADE
OR PIN

FIG. 13

BATTERY

Your tractor has a battery charging system which is sufﬁcient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

PD18H42STA specifications

The Poulan PD18H42STA is a powerful and versatile lawn tractor designed to make mowing easier and more efficient for homeowners and landscapers alike. With its robust build and a range of user-friendly features, the PD18H42STA is ideal for managing medium to large lawns.

One of the standout features of the Poulan PD18H42STA is its 18 horsepower Briggs & Stratton engine, known for efficiency and reliability. The engine provides ample power for cutting and handling various terrain types. Its overhead valve design enhances fuel efficiency and reduces emissions, aligning with modern environmental standards.

The PD18H42STA comes equipped with a 42-inch cutting deck, allowing for a wider cutting path, which means fewer passes over your lawn. The adjustable cutting height feature enables users to select from six different positions, ranging from 1.5 inches to 4 inches, accommodating different grass types and seasonal requirements. This flexibility ensures a clean and even cut, promoting healthy grass growth.

Another notable technology in this tractor is the hydrostatic transmission. This system allows for smooth acceleration and deceleration, providing easy maneuverability, especially in tight spaces. The absence of shifting gears simplifies operation, making it accessible even for those who may not be familiar with riding mowers.

Comfort is paramount in the design of the PD18H42STA. The seat is ergonomically designed with ample cushioning to provide comfort during extended use. The easy-to-use steering wheel allows for precise control, while the foot pedal allows for easy speed adjustments.

Maintenance is straightforward with the Poulan PD18H42STA. The deck wash feature makes it easy to clean the underside of the cutting deck, helping to prevent grass buildup and ensuring optimal performance. Additionally, a removable fuel tank cap facilitates refueling without spills, enhancing convenience.

In summary, the Poulan PD18H42STA combines power, comfort, and technology to deliver an excellent mowing experience. With its reliable engine, efficient cutting deck, and user-friendly features, it stands out as a capable choice for anyone looking to maintain a beautiful lawn with less effort.

Poulan PD18H42STA owner manual Tractor

Models: PD18H42STA