OPERATION

The cutting height range is approximately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

Remove retainer spring and clevis pin which secure each gauge wheel bar.

Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

Replace retainer spring into clevis pin.

Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

019

77

 

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

Select desired height of cut.

Lower mower with attachment lift control.

Start mower blades by engaging attachment clutch

control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

PULL OUT TO

ATTACHMENT LIFT LEVER HIGH POSITION

"ENGAGE"

 

 

 

 

LOW

 

 

POSITION

ATTACHMENT

 

 

CLUTCH SWITCH

 

 

PUSH IN TO

 

 

"DISENGAGED"

 

 

DEFLECTOR SHIELD

02142

 

FIG. 10

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

Choose the slowest speed before starting up or down hills.

Avoid stopping or changing speed on hills.

If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

To restart movement, slowly release parking brake and brake pedal.

Slowly depress appropriate drive pedal to slowest set- ting.

Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

Raise attachment lift to highest position with attachment lift control.

Pull freewheel control out and into the slot and release so it is held in the disengaged position.

Do not push or tow tractor at more than two (2) MPH.

To reengage transmission, reverse above procedure.

13

Page 13
Image 13
Poulan PD25PH48STB To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills, To Transport See Figs

PD25PH48STB specifications

The Poulan PD25PH48STB is a versatile lawn tractor designed to deliver performance and comfort for homeowners looking to maintain their lawns with ease. It is particularly well-suited for those with medium to large yards, providing the necessary power and features to make lawn care more efficient.

One of the standout features of the Poulan PD25PH48STB is its robust 48-inch cutting deck, which allows for a wider cutting path. This is beneficial for covering more ground in less time, reducing the overall time spent mowing the lawn. The deck is designed with a durable steel construction that ensures longevity and resilience against various elements.

The mower is powered by a reliable 25 horsepower Briggs & Stratton engine. This engine combines power with fuel efficiency, offering excellent performance to tackle even the toughest grass conditions. The electric start feature adds convenience, allowing users to start the engine with the turn of a key rather than the traditional method of pulling a cord.

Another notable characteristic of the PD25PH48STB is its six-speed transmission, which provides excellent control and adaptability depending on the mowing conditions. This allows users to adjust their speed based on their preference or the terrain, whether it’s flat or hilly.

The tractor also features an ergonomic seat design, ensuring comfort during extended mowing sessions. The adjustable seat makes it easy to find the perfect riding position, while the easy-to-reach controls enhance the overall user experience. To further enhance comfort, the PD25PH48STB comes equipped with a deck wash port that simplifies cleaning, allowing users to maintain the mower with minimal effort.

For those concerned about safety, this lawn tractor includes an automatic safety shut-off feature that engages when the operator leaves the seat, providing peace of mind while mowing. Additionally, the tight turning radius allows for greater maneuverability, making it easier to navigate around trees, flower beds, and other obstacles in the yard.

Overall, the Poulan PD25PH48STB is an exceptional choice for homeowners looking for a dependable, efficient, and comfortable lawn mowing solution. With its powerful engine, generous cutting deck, user-friendly features, and safety mechanisms, it stands out as a top contender in the lawn tractor market.