OPERATION

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

•Allow one minute for transmission to warm up.This can be done during the engine warm up period.

•The attachments can also be used during the engine warm-up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 12).

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE

 

 

REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD

 

 

BE PURGED AFTER REINSTALLATION BEFORE OPERATING

 

FIG. 12

THE TRACTOR.

 

 

 

• Place tractor safely on level surface with engine off and

 

• If grass is extremely tall, it should be mowed twice to

parking brake set.

 

 

reduce load and possible fire hazard from dried clip-

• Disengage transmission by placing freewheel control

 

 

pings. Make first cut relatively high; the second to the

in freewheeling position (See “TO TRANSPORT” in this

 

desired height.

section of manual).

 

• Do not mow grass when it is wet. Wet grass will plug

• Sitting in the tractor seat, start engine. After the engine

 

 

mower and leave undesirable clumps. Allow grass to

is running, move throttle control to slow position. With

 

dry before mowing.

motion control lever in neutral (N) position, slowly dis-

 

• Always operate engine at full throttle when mow-

engage clutch/brake pedal.

 

 

ing to assure better mowing performance and proper

• Move motion control lever to full forward position and

 

 

discharge of material. Regulate ground speed by se-

hold for five (5) seconds. Move lever to full reverse

 

lecting a low enough gear to give the mower cutting

position and hold for five (5) seconds. Repeat this

 

performance as well as the quality of cut desired.

procedure three (3) times.

 

• When operating attachments, select a ground speed

 

 

NOTE: During this procedure there will be no movement

 

that will suit the terrain and give best performance of

of drive wheels. The air is being removed from hydraulic

15

the attachment being used.

drive system.

 

Page 14 Page 16
Page 15
Image 15
Poulan PK20H48YT manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP
Page 14 Page 16

PK20H48YT specifications

The Poulan PK20H48YT is a versatile and robust riding lawn mower, specifically designed to provide users with an efficient grass cutting experience. This model stands out for its combination of power, performance, and ease of use, making it an ideal choice for homeowners with medium to large lawns.

One of the main features of the Poulan PK20H48YT is its powerful 20 HP Kohler engine. This engine provides ample power for cutting through thick grass and tackling uneven terrain. Coupled with a reliable automatic transmission system, users can easily navigate their lawns without the hassle of shifting gears. The simplicity of operation ensures that both seasoned users and beginners can achieve professional-looking results with minimal effort.

The mower’s cutting deck, measuring 48 inches, allows for a wider path when mowing, reducing the number of passes required and significantly saving time. The deck is constructed from durable materials, designed to withstand the rigors of outdoor use while ensuring longevity. Additionally, the deck height can be easily adjusted, offering six different cutting positions ranging from 1.5 to 4 inches, allowing users to customize their lawn's appearance to personal preferences and grass types.

In terms of technology, the Poulan PK20H48YT features a comfortable and ergonomic operator's seat, enhancing user experience. With a built-in steering wheel and easy-to-reach controls, individuals can maneuver and operate the mower with ease. The model is also equipped with a rear bagger option, enabling grass clippings to be efficiently collected, reducing the need for additional clean-up after mowing.

Safety is a vital consideration in lawn care equipment, and the PK20H48YT does not disappoint. The mower comes with essential safety features such as blade brake and an operator presence system, ensuring the blades stop spinning when the operator leaves the seat.

Another important characteristic of the Poulan PK20H48YT is its durability and maintenance-friendly design. The mower’s robust construction, paired with easy-access maintenance points, simplifies regular upkeep, ensuring the equipment remains in prime working condition for years.

Overall, the Poulan PK20H48YT is a well-rounded riding lawn mower that offers power, efficiency, and user-friendliness, making it a top choice for homeowners seeking quality lawn care solutions. Whether tackling overgrown grass or maintaining a manicured lawn, this model is equipped to handle it all with ease.
Top Page Image Contents