OPERATION

TO ADJUST SKID PLATES (See Fig. 19)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 19

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHOKE CONTROL

THROTTLE PRIMER ENGINE OIL

 

FILL CAP /

 

DIPSTICK

SAFETY

IGNITION

KEY

 

GASOLINE

 

FILLER CAP

 

FUEL SHUT-

 

OFF VALVE

RECOIL

STARTER BUTTON

STARTER

 

HANDLE

POWER CORD PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 20

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 20)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 20)

Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

12

TO START ENGINE

Be sure fuel shut-off valve is in the OPEN position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

Page 12
Image 12
Poulan PO927ES owner manual Before Starting the Engine, Scraper BAR, To Start Engine

PO927ES specifications

The Poulan PO927ES is a powerful and efficient gas-powered snow blower designed to tackle a variety of winter weather conditions. This robust machine combines innovative technology with user-friendly features, making it an ideal choice for homeowners needing to keep their driveways, sidewalks, and other outdoor areas clear of snow.

One of the key features of the PO927ES is its 27-inch clearing width, allowing for substantial snow removal in fewer passes. This makes it perfect for both light and heavy snowfall, ensuring efficiency during winter storms. Additionally, the 12-inch intake height enables the snow blower to handle deeper accumulations, making it suitable for different snowfall conditions.

The Poulan PO927ES is powered by a reliable 305cc engine, delivering ample power to slice through heavy, wet snow with ease. Its recoil start system ensures that users can quickly power on the machine, so they can get to work without delay. This dependable engine provides enough torque to clear even the densest snow, ensuring smooth performance throughout the winter season.

Equipped with a two-stage snow clearing system, the PO927ES efficiently discharges snow through a high-throw chute. The adjustable chute allows users to control the direction and distance of snow discharge, with a range of up to 30 feet. This feature is particularly advantageous in reducing snow mounds and ensuring that cleared areas remain accessible.

User comfort has been prioritized in the design of the PO927ES. The machine features heated hand grips, allowing for prolonged use in cold weather without discomfort. Additionally, its ergonomic controls and easy-to-navigate dashboard put the power of snow removal right at the fingertips of the user.

The snow blower also boasts heavy-duty steel construction, providing durability and longevity. The rugged build is designed to withstand the rigors of snowy conditions, ensuring that it remains a reliable tool for many winters to come.

Furthermore, the Poulan PO927ES is built with an adjustable and self-propelled drive system. This means users can select their preferred speed and power through varying terrain with confidence. The large, rugged tires enhance traction, ensuring stability and control during operation.

In conclusion, the Poulan PO927ES blends power, efficiency, and user-friendliness into a robust snow removal solution. Its impressive features, reliable engine, and thoughtful design make it a go-to choice for homeowners dealing with winter's challenges. Whether it's light flurries or heavy snowfalls, this snow blower rises to the occasion, ensuring that outdoor spaces remain safe and accessible throughout the cold months.