HOW to Start Your Unit, Starting a Cold Engine

ON/OFF Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move the start lever to the START posi- tion.

Starter Handle

Start

Lever

Primer Bulb

Muffler

5.Pull starter rope handle sharply until en- gine starts and runs.

6.Allow unit to run for 5 seconds, then fully squeeze the throttle trigger to disengage the starting system.

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until engine runs smoothly.

3.Pull starter rope sharply while squeezing throttle trigger until engine runs.

NOTE: Normally, the warm starting proce- dure can be used within 5--10 minutes after the unit is turned OFF. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the ON/OFF switch in the ON position. Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter han- dle repeatedly while squeezing throttle trigger until engine starts and runs. This could re- quire pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL: Edger . . . . . . . . . . . . . . . . . . . . . PP1000E Cultivator . . . . . . . . . . . . . . . . . . PP2000T Blower . . . . . . . . . . . . . . . . . . . . PP3000B Brushcutter . . . . . . . . . . . . . . . . PP4000C Pruner . . . . . . . . . . . . . . . . . . . . PP5000P

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL ATTACHMENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

1.Loosen the coupler by turning the knob counterclockwise.

	Upper
Coupler	Shaft
Lower	LOOSEN
Lower
Attachment
TIGHTEN	Knob

2.Press and hold the locking/release button. Locking/Release

Button

	Coupler	Upper Shaft
	Lower Attachment	Upper Shaft
	Lower Attachment

3.While securely holding the engine and upper shaft, pull the attachment straight out of the coupler.

INSTALLING OPTIONAL ATTACH- MENTS

1.Remove the shaft cap from the attach- ment (if present).

2.Position locking/release button of attach- ment into guide recess of coupler.

3.Push the attachment into the coupler until the locking/release button snaps into the primary hole.

4.Before using the unit, tighten the knob se- curely by turning clockwise.

PP136E specifications

The Poulan PP136E is a powerful and reliable chainsaw designed for both professional and household users. This saw is particularly suitable for light to medium cutting tasks, such as trimming trees, cutting firewood, and handling various outdoor chores. It boasts a combination of user-friendly features and advanced technology, making it an ideal choice for anyone looking for an efficient and effective chainsaw.

One of the standout features of the Poulan PP136E is its engine. Powered by a robust 36cc two-cycle engine, it delivers impressive performance while maintaining a lightweight design. This means users can maneuver the chainsaw with ease, reducing fatigue during extended use. The engine is designed with a strong focus on fuel efficiency, allowing for longer run times between refueling.

The chainsaw is equipped with a 16-inch bar and chain, providing a balance between cutting capability and control. This length is versatile enough for various applications without becoming cumbersome. The chain itself is designed for quick adjustments, allowing users to maintain optimal tension for safe and effective cutting.

Another notable feature is the tool-less chain tensioning system, which simplifies the process of adjusting the chain's tension. This is particularly beneficial for users who need to make frequent adjustments on the job. Furthermore, the Poulan PP136E incorporates an automatic oiler, ensuring the chain and bar are lubricated during operation. This not only extends the life of the saw but also enhances cutting performance.

The design of the Poulan PP136E also emphasizes user comfort and safety. It features a reliable safety switch, ensuring that the chainsaw won't accidentally start. The ergonomic handle provides a comfortable grip, allowing users to operate the saw for longer periods without experiencing discomfort.

The lightweight design, combined with technological advancements like anti-vibration handles, minimizes user fatigue. This makes the PP136E a great choice for both seasoned professionals and those new to chainsaw operations.

In conclusion, the Poulan PP136E is a well-rounded chainsaw that combines performance, efficiency, and user-friendly features. Whether you are tackling yard work or professional cutting tasks, this chainsaw offers the reliability and power you need. Its blend of innovative technology and thoughtful design makes it a worthwhile investment for anyone looking to enhance their outdoor maintenance arsenal.

Poulan PP136E HOW to Start Your Unit, Starting a Cold Engine, Starting a Warm Engine

Models: PP136E