MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

(NORMAL OPERATING)

02828

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 12)

Raise mower to highest position to allow access to blades.

Remove blade bolt,

Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

Reassemble blade bolt, lock washer and flat washer in exact order as shown.

Tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

TRAILING

STAR

EDGE UP

 

BLADE

 

 

CENTER

 

HOLE

 

MANDREL

 

ASSEMBLY

 

BLADE BOLT

FIG. 12

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

17

Page 17
Image 17
Poulan PP21H42 manual Tractor, Blade Removal See Fig, Battery

PP21H42 specifications

The Poulan PP21H42 is a powerful and versatile riding lawn mower that is designed to make your lawn care tasks easy and efficient. With its robust features and advanced technology, this mower is well-suited for both residential and small commercial use.

One of the standout characteristics of the Poulan PP21H42 is its 42-inch cutting deck. This size is ideal for maneuvering around obstacles such as trees and flower beds while still allowing for efficient cutting in larger areas. The cutting deck is made from high-quality steel, ensuring durability and longevity even in the toughest mowing conditions.

Powering the Poulan PP21H42 is a reliable Briggs & Stratton engine, known for its efficiency and performance. This engine delivers ample horsepower to tackle thick grass and uneven terrain. The included automatic transmission allows for smooth operation, enabling the operator to easily adjust speed without having to stop and shift gears manually.

The design of the Poulan PP21H42 enhances comfort and ease of use. Its ergonomic seat is adjustable, allowing users of different heights to find their ideal driving position. The mower is equipped with a tight turning radius, making it easier to navigate around obstacles, and the easy-to-access control panel ensures that operators have everything they need at their fingertips.

One of the key technologies featured in the Poulan PP21H42 is its cutting height adjustment feature. With a simple lever, users can adjust the cutting height to one of six different positions, ranging from 1 to 4 inches, allowing for customized cutting according to different lawn types and conditions.

Additionally, this mower comes with a mulching kit option, which finely chops grass clippings and redistributes them back onto the lawn, returning nutrients to the soil and promoting healthier grass growth. The side discharge chute design efficiently disperses clippings without clogging, ensuring a clean and neat finish after mowing.

Safety features are also a priority in the Poulan PP21H42. The mower is equipped with a safety switch that engages when the operator leaves the seat, preventing accidental starts or injuries.

Overall, the Poulan PP21H42 combines performance, comfort, and safety, making it an excellent choice for anyone looking to maintain a well-kept lawn with minimal effort. Whether you have a large yard or a small property, the PP21H42 provides the tools and technology needed for effective lawn care.