BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel handling information in the safety rules sec- tion of this manual before you begin. If you do not understand the fuel handling information do not attempt to fuel your unit. Seek help from someone that does understand the in- formation or call the customer assistance help line at 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slow- ly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on un- leaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gaso- line. Included with this saw is a 3.2 ounce (95 ml) container of Poulan/Weed Eater brand syn- thetic oil. Pour the entire contents of this con- tainer into 1 gallon (4 liters) of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan or Poulan PROR bar and chain oil is recommended to protect your unit against excessive wear from heat and fric- tion. Poulan or Poulan PROR oil resists high temperature thinning.

If Poulan or Poulan PROR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or meth- anol) can attract moisture which leads to sepa-

ration and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine prob- lems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible. The chain brake must be disengaged before cutting with the saw.

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15″ -- 18″ (40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

9

Page 8 Page 10
Page 9
Image 9
Poulan PP3816 AV, PP4218 AV Before Starting Engine Fueling Engine, BAR and Chain Lubrication, Important Points to Remember
Page 8 Page 10

PP3816 AV, PP4218 AV, PP4218 AV specifications

The Poulan PP4218 AV, PP3816 AV, and PP4218 AV chainsaws are renowned for their efficiency, power, and innovative features, making them reliable choices for both amateur and professional users. These models are designed to cater to various cutting needs, from trimming branches to felling larger trees.

The Poulan PP4218 AV is equipped with an 18-inch bar and a powerful 42cc engine, offering a commendable balance of weight and performance. One of its key features is the anti-vibration system, which significantly reduces operator fatigue during extended use. The chainsaw also boasts a tool-less chain tensioning system, making it easy to adjust the chain without needing additional tools. This is especially useful for ensuring optimal cutting performance and safety.

The PP3816 AV, on the other hand, offers a slightly smaller package with a 16-inch bar and a 38cc engine. This model is designed for users who require a lightweight chainsaw for smaller tasks such as pruning and lightweight cutting. It too features the anti-vibration technology, enhancing comfort during operation. The quick start system allows for easier startups, making it accessible to users of all experience levels. Its compact design also provides excellent maneuverability, making it perfect for tight spaces.

The PP4218 AV is very similar to the original PP4218 AV, yet it incorporates further refinements in performance and ergonomics. It remains powerful with its 42cc engine and 18-inch bar but includes enhanced features such as a more efficient air filtration system. This improvement not only extends the life of the engine by keeping it cleaner but also ensures optimal performance even in dusty conditions. Additionally, it maintains the easy access to controls and the comfortable grip design that Poulan is known for, making it a favorite among homeowners and professionals alike.

All three models utilize Poulan's exclusive OxyPower technology, which delivers more power while reducing emissions. This commitment to environmentally friendly technology ensures that users can operate these chainsaws with a focus on sustainability.

In summary, whether you choose the PP4218 AV, PP3816 AV, or stick with the original PP4218 AV, each chainsaw combines power, convenience, and advanced technologies, making them excellent tools for tackling a wide range of cutting tasks.
Top Page Image Contents