ON/OFF Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move the start lever to the START posi- tion.

Starter Handle

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the ON/OFF switch in the ON position. Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter han- dle repeatedly while squeezing throttle trigger until engine starts and runs. This could re- quire pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL:

Edger . . . . . . . . . . . . . . . . . . . . . . PPB1000E Cultivator . . . . . . . . . . . . . . . . . . . PPB2000T Blower . . . . . . . . . . . . . . . . . . . . . PPB3000B Brushcutter . . . . . . . . . . . . . . . . . PPB4000C Pruner . . . . . . . . . . . . . . . . . . . . . PP5000P

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL AT- TACHMENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

1.Loosen the coupler by turning the knob counterclockwise.

Upper Shaft

Coupler

Lower

LOOSEN

Start

Lever

Primer Bulb

Muffler

5.Pull starter rope handle sharply until en- gine starts and runs.

6.Allow unit to run for 5 seconds, then fully squeeze the throttle trigger to disengage the starting system.

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until engine runs smoothly.

3.Pull starter rope sharply while squeezing throttle trigger until engine runs.

NOTE: Normally, the warm starting proce- dure can be used within 5--10 minutes after the unit is turned OFF. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

Attachment

TIGHTEN Knob

2.Press and hold the locking/release button. Locking/Release

Button

Coupler

Upper Shaft

Lower Attachment

 

3.While securely holding the engine and upper shaft, pull the attachment straight out of the coupler.

INSTALLING OPTIONAL ATTACH- MENTS

1.Remove the shaft cap from the attach- ment (if present).

2.Position locking/release button of attach- ment into guide recess of coupler.

3.Push the attachment into the coupler until the locking/release button snaps into the primary hole.

4.Before using the unit, tighten the knob se- curely by turning clockwise.

9

Page 8 Page 10
Page 9
Image 9
Poulan PPB100E HOW to Start Your Unit, Starting a Cold Engine, Starting a Flooded Engine, Operating the Coupler
Page 8 Page 10

PPB100E specifications

The Poulan PPB100E is a highly regarded outdoor power tool designed for homeowners and professionals alike, renowned for its performance and user-friendly features. This versatile blower is ideal for maintaining gardens, yards, and driveways, making it an essential addition to any landscaping toolkit.

One of the standout features of the PPB100E is its lightweight design. Weighing in at just around 8 pounds, this blower is easy to maneuver, allowing users to work for extended periods without experiencing fatigue. This is particularly beneficial for those tackling larger properties or more extensive landscaping projects.

The PPB100E is equipped with a powerful 25cc 2-cycle gas engine, delivering robust performance for efficient leaf and debris clearing. With a maximum airflow velocity of 150 miles per hour, users can count on this blower to swiftly handle various yard waste, from leaves to grass clippings. The combination of power and velocity ensures that even stubborn debris can be cleared away with ease.

Another impressive aspect of the PPB100E is its innovative starting system. The Soft Start technology minimizes the effort needed to start the engine, making it accessible for users of all skill levels. Coupled with a primer bulb, this feature allows for reliable ignition without the frustration often associated with starting gas-powered equipment.

The design of the PPB100E also focuses on user comfort. The blower is ergonomically designed with a cushioned grip, which helps reduce vibrations during operation. This feature is crucial for long-term use, ensuring that users maintain a comfortable hold even during extended sessions. Additionally, the blower is equipped with a second handle that provides better control and maneuverability.

The PPB100E incorporates an easy-to-maintain air filter that enhances the engine's performance and longevity. This air filter can be quickly accessed and cleaned, ensuring optimal airflow and efficiency. Complementing this feature is the blower's fuel-efficient design, which reduces emissions while maximizing runtime.

Overall, the Poulan PPB100E embodies a blend of performance, convenience, and comfort, making it a reliable choice for anyone looking to keep their outdoor space tidy. Its impressive features and technologies showcase Poulan's commitment to quality and user-friendly design, making yard maintenance more accessible and efficient.
Top Page Image Contents