ON/OFF Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move the start lever to the START posi- tion.

Starter Handle

Start

Lever

Primer Bulb

Muffler

5.Pull starter rope handle sharply until en- gine starts and runs.

6.Allow unit to run for 5 seconds, then fully squeeze the throttle trigger to disengage the starting system.

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until engine runs smoothly.

3.Pull starter rope sharply while squeezing throttle trigger until engine runs.

NOTE: Normally, the warm starting proce- dure can be used within 5--10 minutes after the unit is turned OFF. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the ON/OFF switch in the ON position. Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter han- dle repeatedly while squeezing throttle trigger until engine starts and runs. This could re- quire pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL:

Edger . . . . . . . . . . . . . . . . . . . . . PPB1000E Cultivator . . . . . . . . . . . . . . . . . . PPB2000T Blower . . . . . . . . . . . . . . . . . . . . PPB3000B Brushcutter . . . . . . . . . . . . . . . . PPB4000C Pruner . . . . . . . . . . . . . . . . . . . . PPB5000P

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL ATTACHMENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

1.Loosen the coupler by turning the knob counterclockwise.

 

Upper

Coupler

Shaft

Lower

LOOSEN

 

Attachment

 

TIGHTEN

Knob

2.Press and hold the locking/release button. Locking/Release

Button

Coupler

Upper Shaft

Lower Attachment

 

3.While securely holding the engine and upper shaft, pull the attachment straight out of the coupler.

INSTALLING OPTIONAL ATTACH- MENTS

1.Remove the shaft cap from the attach- ment (if present).

2.Position locking/release button of attach- ment into guide recess of coupler.

3.Push the attachment into the coupler until the locking/release button snaps into the primary hole.

4.Before using the unit, tighten the knob se- curely by turning clockwise.

9

Page 8 Page 10
Page 9
Image 9
Poulan PPB250E HOW to Start Your Unit, Starting a Cold Engine, Starting a Warm Engine, Starting a Flooded Engine
Page 8 Page 10

PPB250E specifications

The Poulan PPB250E is a versatile and efficient tool designed for both professional landscapers and homeowners who want to maintain their outdoor spaces with ease. This gas-powered blower offers a combination of power, portability, and user-friendly features, making it a standout option in the competitive market of outdoor power equipment.

One of the key features of the Poulan PPB250E is its reliable 25cc engine. This two-cycle engine is designed to deliver strong air output, enabling users to clear leaves, debris, and grass clippings with minimal effort. The blower produces an impressive airflow of up to 450 CFM (cubic feet per minute), making it highly effective for both small and larger yards. The engine is also designed for fuel efficiency, allowing users to work for longer periods without frequent refueling.

Portability is another significant advantage of the Poulan PPB250E. Weighing in at just 8.5 pounds, it is lightweight and easy to maneuver. The comfortable grip handle and well-balanced design reduce fatigue during extended use, making it suitable for homeowners and professionals alike. The blower features a user-friendly throttle control, allowing for precision adjustments based on the user’s needs and the specific job at hand.

Technologically, the Poulan PPB250E incorporates a primer bulb that simplifies starting the engine. This feature minimizes the hassle typically associated with starting gas-powered equipment, ensuring that users can get to work quickly. Additionally, the blower is equipped with a translucent fuel tank, enabling users to easily monitor fuel levels, which enhances operational efficiency.

The PPB250E also boasts a vibration-dampening system, which further enhances user comfort. By minimizing vibrations, it helps reduce operator fatigue, allowing for longer, more productive sessions. Safety features, such as a protective muffler, are designed to ensure that the tool operates quietly while adhering to environmental standards.

In summary, the Poulan PPB250E is a powerful gas blower that combines performance, portability, and ease of use. With its efficient 25cc engine, impressive airflow, lightweight design, and user-friendly features, it is ideal for anyone looking to keep their outdoor spaces tidy and well-maintained. Whether for residential use or professional landscaping, the Poulan PPB250E stands out as a reliable and effective choice.
Top Page Image Contents