Manuals / Brands / Lawn and Garden / Lawn Mower / Poulan / Lawn and Garden / Lawn Mower

Poulan PRGT22H48A TO REPLACE HEADLIGHT BULB, INTERLOCKS AND RELAYS, TO REPLACE FUSE, TO ADJUST ATTACHMENT LIFT SPRING (See Fig. 34), TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 35)

1 52

Download 52 pages, 2.08 Mb

25

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely

back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run

poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair

Parts section.

TO REPLACE FUSE

Replace with 30 amp automotive-type plug-in fuse. The fuse

holder is located behind the dash.

SERVICE AND ADJUSTMENTS

TO ADJUST ATTACHMENT LIFT SPRING(See Fig. 34)

•While holding spring bushing with wrench, loosen jam

nut.

•Turn adjustment bolt clockwise to extend spring and

reduce lift effort for heavier attachments.

•Turn adjustment bolt counterclockwise for lighter at-

tachments.

•Retighten jam nut against spring bushing.

IMPORTANT: DO NOT ADJUST FOR MAXIMUM SPRING

TENSION WHEN USING LIGHT ATTACHMENTS SUCH

AS A MOWER. ADJUST LIFT LEVER SPRING TO AID IN

LIFTING ATTACHMENT. DO NOT OVERPOWER SPRING.

WHEN REMOVING ATTACHMENT, ALWAYS ADJUST

SPRING TENSION TO ITS LOWEST POSITION.

ADJUSTMENT

BOLT

JAM NUT

ATTACHMENT

LIFT SPRING

SPRING BUSHING

FIG. 34

HEADLIGHT

WIRE

CONNECTOR

FIG. 35

HOOD

TO REMOVE HOOD AND GRILL ASSEMBLY(See Fig. 35)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward

engine and lift off of tractor.

•To replace, reverse above procedures.

Contents

Main MODEL: PRGT22H48A I. GENERAL OPERATION II. SLOPE OPERATION straight gradual SAFETY RULES down Never Do not III. CHILDREN SAFETY RULES WARNING PRODUCT SPECIFICATIONS TABLE OF CONTENTS CUSTOMER RESPONSIBILITIES UNASSEMBLED PARTS Steering Wheel (4) Wheels Mower Seat TOOLS REQUIRED FOR ASSEMBLY TO REMOVE TRACTOR FROM CARTON UNPACK CARTON HOW TO SET UP YOUR TRACTOR CHECK BATTERY (See Fig. 2) TO ROLL TRACTOR OFF SKID (See Opera- tion section for location and function of con- trols) TO DRIVE TRACTOR OFF SKID (See Opera- tion section for location and function of con- trols) INSTALL SEAT (See Fig. 3) ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4) TO ATTACH NOSE ROLLER (See Fig. 5) INSTALL MOWER AND DRIVE BELT (See Figs. 6 and 7) CHECKLIST WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS: CHECK TIRE PRESSURE CHECK MOWER LEVELNESS CHECK FOR PROPER POSITION OF ALL BELTS P KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR. TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8) TO USE CHOKE CONTROL (See Fig. 8) TO USE THROTTLE CONTROL (See Fig. 8) HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE (See Fig. 8) TO MOVE FORWARD AND BACKWARD (See Fig. 8) TO OPERATE MOWER (See Fig. 10) TO TRANSPORT (See Figs. 7 and 11) TO OPERATE ON HILLS TOWING CARTS AND OTHER ATTACH- MENTS TO ADJUST GAUGE WHEELS (See Fig. 9) BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL PURGE TRANSMISSION MOWING TIPS T R A C T 0 R MAINTENANCE SCHEDULE ENGINE SERVICE DATES GENERAL RECOMMENDATIONS BEFORE EACH USE LUBRICATION CHART FRONT WHEEL BEARING ZERK SPINDLE ZERK SPINDLE ZERK FRONT WHEEL BEARING ZERK STEERING SECTOR GEAR TEETH BRAKE OPERATION TIRES OPERATOR PRESENCE SYSTEM BLADE CARE BLADE REMOVAL (See Fig. 13) TRANSAXLE COOLING TRANSAXLE PUMP FLUID CLEAN AIR SCREEN CLEAN AIR INTAKE/COOLING AREAS V-BELTS CLEANING IN-LINE FUEL FILTER (See Fig. 18) ENGINE OIL FILTER AIR FILTER (See Fig. 17) TO LEVEL MOWER HOUSING TO REMOVE MOWER (See Fig. 19) TO INSTALL MOWER TO REPLACE MOWER DRIVE BELT TO ADJUST ATTACHMENT CLUTCH (See Fig. 26) TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 25) TO REPLACE MOTION DRIVE BELT (See Fig. 27) TRANSMISSION REMOVAL/REPLACEMENT A B TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 28) TO ADJUST STEERING WHEEL ALIGNMENT TO START ENGINE WITH A WEAK BATTERY (See Fig. 32) TO REMOVE WHEEL FOR REPAIRS REPLACING BATTERY (See Fig. 33) TO REPLACE HEADLIGHT BULB INTERLOCKS AND RELAYS TO REPLACE FUSE TO ADJUST ATTACHMENT LIFT SPRING (See Fig. 34) TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 35) TO ADJUST THROTTLE CONTROL CABLE (See Fig. 36) TO ADJUST CHOKE CONTROL (See Fig. 37) TO ADJUST CARBURETOR STORAGE BATTERY FUEL SYSTEM ENGINE OIL CYLINDER(S) TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Page SCHEMATIC NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS IGNITION SWITCH RELAY Page ELECTRICAL Page CHASSIS AND ENCLOSURES Page GROUND DRIVE Page STEERING ASSEMBLY ENGINE SPARK ARRESTER KIT ENGINE SEAT ASSEMBLY LIFT ASSEMBLY MOWER DECK 90 90 9118093 94 93 180 95 Page DECALS WHEELS & TIRES Page Page Page LIMITED WARRANTY SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION PARTS AND SERVICE FOR SERVICE OR REPLACEMENT PARTS: NOTE: