Manuals / Poulan / Lawn and Garden / Tiller

Poulan PRRT65B Service And Adjustments, Tiller, TO ADJUST HANDLE HEIGHT See Fig, Tire Care

Models: PRRT65B

1 28

Download 28 pages 61.89 Kb

Page 14

SERVICE AND ADJUSTMENTS

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 20)

Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.

•First loosen handle lock lever.

•Handle can be positioned at different settings between “HIGH” and “LOW” positions.

•Retighten handle lock lever securely after adjusting.

HANDLE

(HIGH POSITION)

HANDLE LOCK

LEVER

HANDLE

(LOW POSITION)

FIG. 20

TIRE CARE

CAUTION: When mounting tires, un- less beads are seated,overinﬂation can cause an explosion.

•Maintain 20 PSI (1.4 kg/cm2) of tire pressure. If tire pressures are not equal, tiller will pull to one side.

•Keep tires free of gasoline or oil which can damage rubber.

TO REMOVE WHEEL (See Fig. 21)

•Place blocks under transmission to keep tiller from tipping.

•Remove outer side shield by removing nuts “A” and “B”.

•Remove inner side shield by removing nuts “C” and “D”.

•Remove hairpin clip and clevis pin from wheel.

•Remove wheel and tire.

•Repair tire and reassemble.

	CLEVIS
	PIN
	NUT “C”
	NUT
	“D”
	HAIRPIN
	CLIP
	NUT “B”	INNER SIDE
	NUT “A”	INNER SIDE
	NUT “A”	SHIELD
	OUTER SIDE	SHIELD
	SHIELD

FIG. 21

14

Image 14

Poulan PRRT65B Service And Adjustments, Tiller, TO ADJUST HANDLE HEIGHT See Fig, Tire Care, TO REMOVE WHEEL See Fig

Contents

IMPORTANT MANUAL MODELPRRT65B REAR TINE TILLERSAFE OPERATION PRACTICES FOR WALK-BEHIND POWERED ROTARY TILLERS SAFETY RULESMAINTENANCE AND STORAGE TRAININGCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS 7-10CONTENTS OF HARDWARE PACK ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY OPERATOR’S POSITION See FigASSEMBLY INSTALL HANDLE See Figs. 3, 4, andUNPACKING CARTON See Fig REMOVE TILLER FROM CRATE ATTACH CLUTCH CABLE See FigCONNECT SHIFT ROD See Fig CHECK TIRE PRESSUREKNOW YOUR TILLER MEETS ANSI SAFETY REQUIREMENTSOPERATION DEPTH STAKE See Fig HOW TO USE YOUR TILLERSTOPPING See Fig TINE OPERATION - WITH WHEEL DRIVETO TRANSPORT TURNINGOUTER SIDE SHIELDS See Fig BEFORE STARTING ENGINECULTIVATING TINE SHEAR PINSTILLING HINTS OPERATIONLUBRICATION CHART MAINTENANCEMAINTENANCE SCHEDULE GENERAL RECOMMENDATIONSDo not touch hot mufﬂer or cylinder ﬁns as contact may cause burns ENGINEAIR FILTER See Fig TO CHANGE ENGINE OIL See Figs. 16 andMUFFLER CLEANINGCOOLING SYSTEM See Fig SPARK PLUGTILLER SERVICE AND ADJUSTMENTSTO ADJUST HANDLE HEIGHT See Fig TIRE CARETO REPLACE GROUND DRIVE BELT See Figs. 22 and GROUND DRIVE BELT ADJUSTMENT See FigTO REMOVE BELT GUARD See Fig SERVICE AND ADJUSTMENTSTINE REPLACEMENT See Figs. 24, 25, and SERVICE AND ADJUSTMENTSSERVICE AND ADJUSTMENTS TO ADJUST THROTTLE CONTROL CABLE See FigTO ADJUST CARBURETOR ENGINEFUEL SYSTEM STORAGEOTHER ENGINE OILTROUBLESHOOTING POINTS TILLER - - MODEL NUMBER PRRT65B REPAIR PARTSHANDLE ASSEMBLY PARTREPAIR PARTS MAINFRAME, LEFT SIDEKEY PART NO. NO. DESCRIPTION TILLER - - MODEL NUMBER PRRT65BBumper MAINFRAME, RIGHT SIDE166532 REPAIR PARTSTRANSMISSION REPAIR PARTSTILLER - - MODEL NUMBER PRRT65B PARTTILLER - - MODEL NUMBER PRRT65B TINE SHIELDREPAIR PARTS KEY PART NO. NO. DESCRIPTIONTILLER - - MODEL NUMBER PRRT65B TINE ASSEMBLYREPAIR PARTS PARTTILLER - - MODEL NUMBER PRRT65B DECALSREPAIR PARTS KEY PART NO. NO. DESCRIPTIONLIMITED WARRANTY PARTS AND SERVICE FOR SERVICE OR REPLACEMENT PARTS