SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 31)

The transaxle should be in neutral when the gear shift lever is in neutral (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral.

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT

NEUTRAL

LEVER

LOCK

 

GATE

 

ADJUSTMENT

 

BOLT

Fig. 31

TO REMOVE WHEEL (See Fig. 32)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

Fig. 32

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO START ENGINE WITH A WEAK BATTERY (See Fig. 33)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR

FULLY CHARGED

DEAD BATTERY

BATTERY

Fig. 33

22

Page 21 Page 23
Page 22
Image 22
Poulan PXT12530 Transaxle Gear Shift Lever Neutral Adjustment See Fig, To Remove Wheel See Fig, Front Wheel TOE-IN/CAMBER
Page 21 Page 23

PXT12530 specifications

The Poulan PXT12530 is a robust and versatile string trimmer designed for homeowners and landscapers who value efficiency and power in their gardening tools. This model boasts an array of features and technologies that make it a standout choice for tackling both small and large yard maintenance tasks.

One of the main features of the Poulan PXT12530 is its lightweight design. Weighing in at a mere 12 pounds, this string trimmer is easy to maneuver, reducing fatigue during extended use. The trimmer also features a curved shaft, which enhances control and provides a comfortable grip, allowing users to reach tight spaces and navigate around obstacles with ease.

Powering the PXT12530 is a dependable 25cc two-cycle engine that delivers ample power for various trimming tasks. This engine ensures that users can tackle overgrown grass and weeds without straining the equipment. The trimmer is equipped with a centrifugal clutch that engages the cutting head only when the throttle is pulled, enhancing safety and improving user control.

Another notable characteristic of the Poulan PXT12530 is its dual-line cutting system. This feature allows for a wider cutting swath, effectively reducing the time needed to complete trimming tasks. The trimmer head is designed to accept .065-inch line, making reloading quick and straightforward. Additionally, it comes with a bump feed mechanism, which automatically feeds more line with a simple tap on the ground, providing convenience and efficiency while you work.

The PXT12530 also emphasizes user comfort through its anti-vibration technology. This system significantly reduces vibrations during operation, making it more comfortable for the user and helping to maintain focus during prolonged use. Coupled with its adjustable handle, the trimmer enables personalized adjustments to suit different user heights, promoting ergonomic handling.

Durability is another key aspect of the Poulan PXT12530. Constructed with high-quality materials, this trimmer is built to withstand the demands of regular use. The protective guards around the cutting head not only enhance safety but also minimize wear and tear.

In conclusion, the Poulan PXT12530 combines practicality, power, and user-friendly features, making it an excellent choice for anyone looking to maintain their yard efficiently. Its lightweight design, powerful engine, dual-line system, and comfort features all contribute to an impressive performance, setting it apart in the realm of string trimmers. Whether you're tackling routine lawn maintenance or preparing your yard for a special occasion, the PXT12530 is a reliable companion that gets the job done effectively.
Top Page Image Contents