Manuals / Poulan / Lawn and Garden / Lawn Mower

Poulan PXT16542 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Models: PXT16542

1 48
Download 48 pages 34.07 Kb
Page 19
Image 19

SERVICE AND ADJUSTMENTS

If “jumper cables” are used for emergency starting, use the following procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR

FULLY CHARGED

DEAD BATTERY

BATTERY

FIG. 23

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining bolt and nut. Tighten securely.

•Lower seat pan.

SEAT PAN

02602

Fig. 24

19

TERMINAL

 

NUT

BOLT

COVER

 

 

 

 

 

POSITIVE

 

 

NEGATIVE

(RED)

 

 

 

 

(BLACK)

CABLE

 

 

 

 

CABLE

 

02603

 

FIG. 25

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02495

Fig. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

Page 18 Page 20
Page 19
Image 19
Poulan PXT16542 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, To Adjust Throttle Control Cable
Page 18 Page 20

PXT16542 specifications

The Poulan PXT16542 is a robust and efficient lawn mower designed for homeowners seeking a reliable and powerful cutting tool for their gardens. Boasting a 42-inch cutting deck, this riding mower is perfectly suited for medium to large lawns, enabling efficient coverage and reduced mowing time.

One of the standout features of the PXT16542 is its powerful 16.5 HP Briggs & Stratton engine. This engine delivers optimized performance with substantial torque, ensuring seamless maneuverability and cutting power on various terrains. The integrated automatic transmission further enhances the mowing experience by allowing smooth speed adjustments, making it easy to navigate around obstacles and uneven surfaces.

A crucial technology in the PXT16542 is its cutting system, featuring a dual-blade design that provides a clean and precise cut every time. With multiple height adjustment settings, users can customize the cutting height to suit their lawn's needs, whether they prefer a close trim or a higher grass finish. This flexibility is essential for maintaining a healthy lawn and promoting robust growth.

The Poulan PXT16542 is also designed for user comfort and convenience. Its ergonomic seat ensures a comfortable riding experience, even during extended mowing sessions. Easy-to-reach controls make operation intuitive, while the easy-access fuel tank simplifies refueling. The inclusion of a tight turning radius allows for exceptional maneuverability, making it easy to navigate tight spots or flowerbeds without damaging the landscape.

Durability and maintenance are prioritized in this mower’s design. The rugged construction and high-quality materials used in the PXT16542 contribute to its longevity and reliability. Additionally, the mower comes with maintenance points conveniently located for easy access, allowing for quick checks and upkeep, which ultimately prolongs the life of the machine.

In summary, the Poulan PXT16542 is an ideal choice for homeowners needing a reliable, user-friendly riding mower. With its powerful engine, versatile cutting capabilities, user-centric design, and durable construction, this mower stands out as a dependable partner for lawn care, ensuring that your garden remains in pristine condition throughout the mowing season.