Poulan TE475, TE475Y Assembly, Cutting Safety, Transporting and Storage, Attaching Shield

CUTTING SAFETY

WARNING: Inspect the area before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by or become entangled in line. Hard objects can damage the trimmer head and be thrown causing serious injury.

S Use only for trimming, scalping, mowing, edging and sweeping. Do not use for prun- ing or hedge trimming.

SKeep firm footing and balance. Do not over-

reach.

SKeep all parts of your body away from muffler

and spinning line. Keep engine below waist level. A hot muffler can cause serious burns.

SCut from your right to your left. Cutting on left side of the shield will throw debris away from the operator.

SUse only in daylight or good artificial light. S Use only for jobs explained in this manual.

TRANSPORTING AND STORAGE

S Allow engine to cool; secure unit before stor- ing or transporting in vehicle.

S Empty the fuel tank before storing or trans- porting the unit. Use up fuel left in the carbure- tor by starting the engine and letting it run until it stops.

S Store unit and fuel in area where fuel vapors cannot reach sparks or open flames from wa- ter heaters, electric motors or switches, fur- naces, etc.

S Store unit so line limiter blade cannot acciden- tally cause injury. The unit can be hung by the shaft.

S Store unit out of reach of children.

SAFETY NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnor- mal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti--vibration system does not guarantee the avoidance of these problems. Users who oper- ate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

SPECIAL NOTICE: This unit is equipped with a temperature limiting muffler and spark ar- resting screen which meets the requirements of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washing- ton require by law that many internal combus- tion engines be equipped with a spark arresting screen. If you operate in a locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. For normal homeowner use, the muffler and spark arresting screen will not require any ser- vice. After 50 hours of use, we recommend that your muffler be serviced or replaced by your au- thorized service dealer.

ASSEMBLY

WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure.

Examine parts for damage. Do not use dam- aged parts.

NOTE: If you need assistance or find parts missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the empty fuel tank.

Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.

ADJUSTING THE ASSIST HANDLE

1.Loosen wing nut on handle.

2.Pivot the handle to a comfortable position; retighten wing nut.

Wing Nut

Groove

ATTACHING SHIELD

WARNING: The shield must be prop- erly installed. The shield provides partial protec- tion from the risk of thrown objects to the opera- tor and others and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on underside of shield) is sharp and can cut you.

For proper orientation of shield, see KNOW YOUR TRIMMER illustration in OPERATION section.

1.Remove wing nut from shield.

2.Insert bracket into slot as shown.

3.Pivot shield until bolt passes through hole in bracket.

4.Securely tighten wing nut onto bolt.

PIVOT Shield Slot

Bracket

Line Limiter

Blade

Wing

Nut

3