HOW to Stop Your Unit, Operating Position

This engine is certified to operate on un- leaded gasoline. Gasoline must be mixed with a good quality 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eaterr brand oil is recom- mended. (A 40:1 ratio is obtained by mixing

3.2ounces of oil with 1 gallon of unleaded gasoline). When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules under FUEL SAFETY.

Starting Position

HOW TO STOP YOUR UNIT

To stop engine, move ON/OFF switch to the OFF position.

S If engine does not start in 5 pulls, follow instructions in STARTING A COLD EN- GINE.

OPERATING POSITION

ALWAYS WEAR:				Eye
ALWAYS WEAR:				Eye

Protection

Long Pants

Heavy Shoes

Cut from your right to your left.

TRIMMER LINE ADVANCE

The cutting head advances line automatically. Do not tap head on the ground to advance line. This may break parts and cause cutting head to malfunction.

Upon unit start up, the line will advance auto- matically to the correct cutting path length. Always keep the shield in place when the tool is being operated.

TWIST-N-EDGE

SPull the tab toward the engine.

Choke lever

Trigger

Primer Bulb

Muffler

STwist the tube to the edging position; release the tab.

Tab

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

SSet unit on a flat surface.

S	Move ON/OFF switch to the ON position.
S	Slowly press the primer bulb 6 times.
S Move choke lever to FULL CHOKE posi-
	tion.
S Squeeze the throttle trigger fully and hold
	through all remaining steps.
S	Pull starter rope handle sharply 6 times.

REPLACING THE LINE

Pre--wound spools offer the most convenient method for replacing line and ensuring opti- mum performance.

S Replacement spools are color--coded to ensure use of the correct spool with your unit. Be sure to use the same color spool as the existing spool.

NOTE: Always clear dirt and debris from cut- ting head components when performing any type of maintenance.

SHold spool and unscrew cap by turning in the direction shown on top of the cap.

SRemove line guide ring and spool.

S Move choke lever to HALF CHOKE posi-

tion.

S Pull starter rope handle no more than 6

pulls, until engine runs.

S Allow engine to run 10 seconds, then move

choke lever to OFF CHOKE position.

RESTARTING A WARM ENGINE

Cap

Line guide ring

Spool

SMove ON/OFF switch to the ON position. S Move choke lever to OFF CHOKE position. S Pull starter rope handle until engine runs.

SUse a pre--wound spool or refill spool with line. If using a pre--wound spool, remove tape strip from line and spool.

TE 400 CXL specifications

The Poulan TE 400 CXL is a robust electric chainsaw engineered for both homeowners and professionals seeking power, efficiency, and reliability. As part of the esteemed Poulan brand, this chainsaw is designed to handle various cutting tasks, from trimming branches to felling moderate-sized trees.

One of the standout features of the TE 400 CXL is its powerful 40-volt lithium-ion battery, providing ample runtime and charging convenience. The battery technology enables users to enjoy the freedom of cord-free operation while delivering performance comparable to gas-powered models. With an efficient power management system, this chainsaw maximizes battery life, allowing users to complete extensive cutting jobs without frequent interruptions.

The TE 400 CXL boasts a 16-inch cutting bar, striking an ideal balance between maneuverability and cutting capacity. This length is suitable for trimming smaller limbs and larger branches, providing versatility for various gardening and landscaping tasks. The automatic oiler is another significant feature of the chainsaw, ensuring that the cutting chain remains lubricated for smoother operation and reduced wear. This system minimizes the risk of overheating, prolonging the lifespan of the equipment while enhancing overall cutting performance.

With a weight of just over 10 pounds, the Poulan TE 400 CXL is designed for ease of use, minimizing fatigue during extended periods of operation. The ergonomic handle, coupled with an intuitive design, provides comfortable handling, making it suitable for users of all skill levels. Safety features, such as a brake system and a chain catch, further enhance user protection, ensuring that accidents are minimized during operation.

The chainsaw features a manageable chain tensioning system that allows for quick adjustments without the need for additional tools. This user-friendly design reflects Poulan's commitment to convenience and efficiency, making regular maintenance easier for the average user.

In terms of performance, the TE 400 CXL delivers consistent cutting speed with its high-performance motor, allowing users to tackle various materials with ease. Additionally, its eco-friendly operation produces lower emissions, aligning with a growing demand for environmentally-conscious tools.

In conclusion, the Poulan TE 400 CXL is a powerful, versatile, and user-friendly electric chainsaw suitable for various cutting tasks. With its advanced features, ergonomic design, and efficient battery technology, it stands as a reliable choice for anyone in need of an effective and simple cutting solution.

Poulan TE 400 CXL HOW to Stop Your Unit, Operating Position, Trimmer Line Advance, Twist-N-Edge

Models: TE 400 CXL