19.Make your workshop child proof with padlocks, master switches or by removing starter keys.

20.Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury.

21.Maintain a balanced stance at all times so that you do not fall or lean against moving parts. Do not overreach or use excessive force to perform any machine operation. Stand to the side out of line with the table and make sure no one else is standing in line with the table.

22.Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely.

23.Maintain tools with care. Keep knives sharp and clean for the best and safest performance. Dull tools increase noise levels and can cause kickbacks and glazed surfaces. Broken gibs/knives that are not securely locked in the cutterhead can be thrown out of the planer causing severe or fatal injury as well as severe damage to the machine. Follow instructions for lubricating machine and changing accessories. Use recommended accessories; improper accessories may be hazardous.

24.Do not attempt to plane boards shorter than 10” (254mm) in length without butting a board of equal thickness behind it to help it through the planer. Be sure the last board of a butted sequence is 10” or longer.

25.Do not feed stacked boards through a planer; a kickback may occur causing severe or fatal injury.

26.Do not plane a board with loose knots or with nails or any foreign material on its surface. Twisted, warped, or wind-in stock should first be jointed on one surface before attempting to plane a parallel surface on the planer. Serious stock flaws cannot be removed by use of a planer alone.

27.If the board being planed stops feeding, disengage or turn the feed off and turn the power off. Wait until the cutterhead comes to a complete stop before lowering the table to remove the board. Never lower the table with the power on and the stock still in the machine, as a kickback can occur.

28.Keep hands outside of the machine. Never reach under the guards to try to clear stock that has stopped feeding. When starting a cut, do not have any part of the hands under that part of the board that is over the table; the infeed roller will engage the board and force it down against the table causing a pinching action.

29.Disconnect machine from power source before cleaning. Use a brush or compressed air to remove chips or debris — do not use your hands.

30.Do not stand on the machine. Serious injury could occur if the machine tips over.

31.Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes to a complete stop.

32.Remove loose items and unnecessary work pieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly even death.

- - SAVE THESE INSTRUCTIONS - -

5

Page 4 Page 6
Page 5
Image 5
Powermatic 201HH operating instructions
Page 4 Page 6

201HH specifications

The Powermatic 201HH is a highly regarded 8-inch jointer, renowned for its robust construction, precision, and advanced technology. This machine is particularly well-suited for both professional woodworkers and serious hobbyists who demand the best performance from their tools.

One of the standout features of the Powermatic 201HH is the Helical Cutterhead. This technology distinguishes it from standard jointers featuring straight knives. The helical design incorporates numerous small, square inserts that can be rotated or replaced when worn, significantly extending the overall life of the cutterhead. The helical arrangement reduces noise during operation and provides a much smoother finish on the workpiece, minimizing the need for additional sanding.

Adjustability is another area where the Powermatic 201HH excels. It boasts an easy-to-use tables adjustment mechanism that allows users to fine-tune the infeed and outfeed tables for precise jointing. This feature is essential to ensure a perfectly flat and even surface on all types of wood. The large tables, measuring 74 inches in length, provide ample support for larger workpieces, making it easier to manage and maneuver materials during operation.

The 201HH also comes equipped with a powerful 3 HP motor that drives the machine with reliability and performance. This motor is a key component in delivering consistent power and maintaining speed even under heavier workloads. Coupled with a strong base and solid construction, the jointer maintains stability during operation, which contributes to both safety and precision.

Added convenience comes in the form of an integrated dust collection port, which facilitates cleaner operation by effectively managing sawdust and shavings. This reduces cleanup time and creates a more pleasant working environment.

Moreover, the design of the Powermatic 201HH incorporates safety features, including a push block that assists in guiding stock through the machine, minimizing the risk of injury. The solid build quality and attention to detail in the engineering provide confidence to users that they are working with a reliable tool that will stand the test of time.

In summary, the Powermatic 201HH offers an impressive array of features including a helical cutterhead, extensive adjustability, a powerful motor, efficient dust collection, and strong safety measures. These characteristics make it a top choice for anyone looking to achieve exceptional results in their woodworking projects.
Top Page Image Contents