|
| Operating | Nominal Size | 500 fpm | Media | Weight | |
|
| Rating | |||||
| Efficiency | Limit ºF | Area | Each | |||
| H x W x D (inch) | ||||||
|
|
| |||||
|
|
|
| cfm | pd | (sq. ft.) | (lbs) |
|
| 750 | 24 x 24 x 12 | 2000 | .45 | 140 | 26 |
|
| 24 x 12 x 12 | 1000 | 69 | 21 | ||
|
| ||||||
|
| 900 | 24 x 24 x 12 | 2000 | .50 | 175 | 28 |
|
| 24 x 12 x 12 | 1000 | 90 | 22 | ||
|
|
|
| ||||
|
| 750 | 24 x 24 x 12 | 2000 | .55 | 140 | 26 |
|
| 24 x 12 x 12 | 1000 | 69 | 21 | ||
|
| ||||||
|
| 900 | 24 x 24 x 12 | 2000 | .60 | 175 | 28 |
|
| 24 x 12 x 12 | 1000 | 90 | 22 | ||
|
|
|
| ||||
|
| 750 | 24 x 24 x 12 | 2000 | .65 | 140 | 26 |
|
| 24 x 12 x 12 | 1000 | 69 | 21 | ||
|
| ||||||
|
| 900 | 24 x 24 x 12 | 2000 | .70 | 175 | 28 |
|
| 24 x 12 x 12 | 1000 | 90 | 22 | ||
|
|
|
|
Notes:
1.PD represents clean pressure drop in inches w.g. The recommended final pressure drop is 2.5 inch w.g.
2.Operation down to zero velocity is satisfactory for all models.
3.Efficiencies are average and are based on ASHRAE Standard 52.1 and 52.2 dust spot test methods. Performance values stated may be averages typical of the products listed. Contact factory for actual perform- ance test reports on specific products.
4.Perfmormance values shown in this publication may be averages or estimates intended to generally represent product styles. Always contact factory for latest actual test data on specific Flanders Precisionaire models.
| Guide Specifications | ||
1.0 | General | 2.3 Expanded metal aluminized steel faceguards | |
1.1 High temperature rigid filters shall be |
| shall be installed on the air entering and air leav- | |
| ing sides. | ||
| PrecisionCell HT separator type as manufactured |
| |
|
|
| |
| by Flanders. | 2.4 A 1/2” “T” strap shall be installed on the down- | |
1.2 Filter sizes and temperature ranges shall be as |
| stream side and 1/2” horizontal strap on the air | |
| entering side. | ||
| scheduled on the drawings. |
| |
|
|
| |
2.0 | Filter Construction | 3.0 Performance | |
|
| ||
2.1 Filters shall be constructed by pleating a contin- | 3.1 | Initial and final resistance shall not exceed the | |
| scheduled values. | ||
| uous sheet of |
| |
|
|
| |
| into closely spaced pleats with | 3.2 Media area shall equal that of the scheduled | |
| corrugated aluminum separators. |
| high temperature filter. |
2.2 The filter pack shall be sealed into a 24 ga. | 3.3 | The manufacturer shall guarantee performance | |
| aluminized steel frame with |
| as outlined in section 7.4 of ARI Standard 800. |
| sealant. |
|
|
|
|
|
|
Flanders - PrecisionAire
Foremost in Air Filtration Toll Free: 1-800-637-2803
REPRESENTED BY: