2.With the help of a second person, carefully tip the Upright Base (97) down as shown. (Note: It may be help- ful to place your foot on one of the Extension Legs [92] as you tip the Uprights.) Make sure that the Extension
Legs remain in the Uprights.
Attach each Extension Leg (92) with two Extension Leg Bolts (96) and two 1/4” Washers (39) as shown. Thread a Leveling Foot (95) into each side of the Upright Base (97); do not thread the Leveling Feet fully into the
Upright Base.
Attach the two Base Pads (99) to the Upright Base (97) in the locations shown with two 1” Tek Screws (80).
With the help of a second person, raise the Upright Base
(97)to the vertical position.
3.Remove the Latch Knob (88) from the Latch Pin (84). Make sure that the Latch Pin Collar (56) and the Spring
(34)are on the Latch Pin. (Note: If there are two Latch Pin Collars, place them on each side of the Spring.) Insert the Latch Pin into the Latch Housing (82) and tighten the Latch Knob onto the Latch Pin.
4.Refer to drawing 4c. With the help of a second person, hold the Console Base (101) near the Uprights (80, 84). Look under the Console Base and locate the wires on the sides of the Console Base. Make sure that the wires are not routed through the openings for the Trays (109, 111). Drawing 4a shows the correct route for the wires. Drawing 4b shows an incorrect route.
Refer to drawing 4c. Cut the plastic ties holding the Wire Harness (74) and the pulse wire in the Uprights (80, 84).
Locate the Wire Harness (74) and pulse wire in the Uprights (80, 84). Connect the Wire Harness and the pulse wire to the connectors on the sides of the Console Base (101). Make sure to connect the connectors properly (see the inset drawings). IF THE CONNEC-
TORS ARE NOT CONNECTED PROPERLY, THE CON- SOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn a connec- tor and try to insert it again. Insert the excess Wire Harness and pulse wire up into the Console Base.
6
2 |
|
|
|
| 99 |
|
|
|
|
| |
|
|
|
|
| 80 |
| 99 |
|
|
|
|
|
|
|
|
| 96 |
|
| 80 |
|
| 95 |
|
|
| 39 |
| |
|
|
|
|
| |
|
|
| 97 | 92 | 96 |
|
|
|
|
| |
| 39 | 96 |
|
|
|
|
|
|
|
| |
97 |
|
| 95 |
|
|
|
|
|
|
| |
92 | 39 | 96 |
|
|
|
3 |
|
|
|
|
|
|
| 82 |
|
|
|
| 125 |
|
|
|
|
|
|
| 34 |
|
|
|
|
|
| 84 |
|
|
|
| 56 |
|
|
4a |
|
| 4b |
|
|
| Correct |
|
| Incorrect |
|
4c |
|
|
|
|
|
| 111 | 109 |
|
| |
|
|
|
|
| |
| 74 | 101 |
|
|
|
|
|
|
|
| |
| 80 |
|
| 84 |
|
| Pulse |
74 | Wire |
|
