ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench

and your own phillips screwdriver and rubber mallet .

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

1. With the help of a second person, carefully raise the

1

 

 

 

treadmill to the upright position as shown at the right.

 

 

 

 

 

 

 

While a second person tips the treadmill to one side

 

 

 

 

and holds it, insert one of the Extension Legs (102) into

 

 

 

 

the treadmill as shown. Make sure that the Extension

 

 

 

 

Leg is turned so the Base Pad (99) is on the bottom.

 

 

 

 

Next, tip the treadmill to the other side and insert the

 

 

 

 

other Extension Leg (not shown) in the same way. Lower

 

 

 

 

the side of the treadmill so that both Extension Legs

 

 

 

102

(102) are resting flat on the floor.

 

 

 

 

 

 

 

 

 

 

 

99

2. With the help of a second person, carefully lower the

2

 

 

 

treadmill frame and then tip the Uprights (69) down as

 

 

 

 

 

 

 

shown. Make sure that the Extension Legs (102) remain

 

 

 

 

in the Uprights.

 

 

 

 

Attach each Extension Leg (102) with two of the four 3/4Ó

 

99

 

 

 

 

 

 

Screws (100) as shown.

 

Frame

 

 

With the help of a second person, carefully tip the

 

 

 

69

Uprights (69) back to the vertical position.

 

 

 

 

69

 

 

100

Note: One replacement Base Pad (99) may be included.

 

 

102

 

 

 

Use the extra Pad if one becomes worn or needs to be re-

99

100

 

placed.

 

102

 

 

 

 

 

 

 

 

 

3. There may be a plastic tie inside the post on the right

3

 

 

 

Upright (69). If there is, insert the plastic tie through a

 

 

 

 

 

 

 

Handrail Extension (66) and insert the Handrail Extension

 

Tab

76

81

into the post as shown. Make sure that the indicated holes

 

 

are on top. Tap the Handrail Extension with a rubber mallet

 

 

67

78

 

 

Holes

 

 

 

to fully insert it. Attach the Handrail Extension with two 1/2Ó

 

Cutout

 

 

 

 

Screws (67) as shown.

 

 

 

69

 

 

75

 

Identify the Right Foam Grip (75), which has a large cutout

 

 

 

 

 

66

Post

in the left side for the Pulse Bar (76). Slide the Right Foam

 

 

 

 

 

Grip as far as possible onto the post on the right Upright

 

Tie

 

(69). Make sure the tab on the Foam Grip inserts into the

 

 

 

 

Console Base (81). It may be helpful to use soapy water on

 

 

 

 

the Handrail Extensions (66).

 

 

 

 

6

Page 6
Image 6
ProForm PFTL79100 user manual Assembly, Your own phillips screwdriver and rubber mallet