2. With the help of a second person, carefully tip | 2 |
|
|
|
|
the treadmill onto its right side as shown. |
|
|
|
| |
|
|
|
|
| |
Insert the other Extension Leg (89) into the base | 84 |
|
|
|
|
|
|
|
| 65 | |
of the Uprights (84) as shown. Hold two |
|
|
|
| |
22 |
|
|
|
| |
Extension Leg Nuts (67) in the bottom of the |
|
|
|
| |
Extension Leg. Next, insert two Extension Leg | 82 |
| 22 |
| |
Bolts (65) into the top of the Extension Leg, and |
|
|
|
| |
firmly tighten the Extension Leg Bolts into the |
|
|
|
|
|
Extension Leg Nuts. |
|
|
|
| 58 |
|
|
|
|
| |
Attach two Base Pads (82) to the base of the |
|
| 67 | 89 |
|
Uprights (84) with two 3/4” Tek Screws (22). |
|
|
|
| |
|
|
|
|
| |
With the help of a second person, carefully raise |
|
|
|
|
|
the treadmill so that all four Base Pads (22) are |
|
|
|
|
|
on the floor and the Frame (58) is in a vertical |
|
|
|
|
|
position (see drawing 3). |
|
|
|
|
|
3. Make sure that the sleeve has been slid over | 3 |
|
|
|
|
hole 1 and that the latch knob is locked into hole |
|
|
|
| |
|
|
|
|
| |
1. Pull on the sleeve to make sure it is locked |
|
|
|
|
|
into place. |
|
|
|
|
|
Next, make sure that the latch knob is locked | Hole 2 |
|
| ||
|
|
|
|
| |
into hole 2. If it is not, pull out the tube until you |
|
|
| Latch Knob | |
see hole 2 and then slide the tube back in until |
|
|
| ||
|
|
|
|
| |
the latch knob locks into hole 2. | Tube |
|
|
| Hole 1 |
|
|
|
| ||
|
| Sleeve |
| ||
4. Remove the plastic ties from the ends of the | 4 |
| 58 |
|
|
Latch Shock (69). |
|
|
| ||
|
|
|
| ||
Hold the Latch Shock (29) with the large barrel |
|
|
|
|
|
and latch knob positioned as shown; make sure | 30 |
| 50 |
| |
all of the holes are aligned (see the inset draw- |
|
| |||
|
|
| Top | ||
|
|
|
| ||
ings). Next, attach the lower end of the Latch |
|
|
|
| |
|
|
|
|
| |
Shock to the bracket on the Upright (84) with the |
|
|
|
| Holes |
Lower Latch Shock Bolt (39) and a Nut (30). | Latch Knob |
|
| 29 | |
|
|
|
| ||
Then, attach the upper end of the Latch Shock |
|
|
|
|
|
(29) to the bracket on the Frame (58) with the |
|
|
| Large |
|
Upper Latch Shock Bolt (50) and a Nut (30). |
|
|
|
| |
|
|
| Barrel |
| |
Note: It may be necessary to move the Frame |
|
|
|
| |
|
|
| 84 |
| |
back and forth to align the Latch Shock with the |
|
|
|
| |
Bracket. |
|
|
|
| Holes |
|
|
|
|
| |
| 30 |
|
|
| Bottom |
|
|
| 39 |
| |
|
|
|
|
| |
| 7 |
|
|
|
|
