PS Audio P1000 quick start Warranty and Service, Safety Instructions, Specifications

Warning Overview

off using the front panel power button, let it sit for a few seconds and power it back up. If the “FAULT”

Warranty and Service

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the enclosure. Refer ser- vicing to qualified personnel only.

To prevent electric shock, use a 3 prong, grounded type power cable.

Any change or modifications not expressly approved in the manual could void your war- ranty.

Safety Instructions

Any turntable or equipment with AC synchro- nous motors, such as some cooling fans should not be used with MultiWave II. This equipment must be used with 60Hz SineWave mode, or connected to the Filtered AC zone outlets.

We recommend the use of the SineWave [SINE] or TubeWave [TWAVE] with any type of tube based audio products.

Read the operating instructions provided with the P1000.

Retain the operating instructions for later use and reference.

Unplug the P1000 from the wall outlet before changing the fuse or performing any cleaning or service.

Do not operate the P1000 near water. Avoid placement near a water reservoir or excessive moisture.

The Power Plant P1000 is a power regenerator capable of delivering the highest level of AC per- formance to all audio and video components.

The PS Audio Power Plant P1000 is designed to operate as a stand-alone power management device, or as part of a larger power management system. In many cases one P1000 will be all that is necessary to protect, clean and regener- ate power for any audio system or home theater system.

The P1000 has two power delivery zones: Eight outlets produce “Regenerated AC” with MultiWave II™. Two outlets pass “Filtered AC” by filtering power with Ultimate Outlet™ technology.

The Regenerated AC zone is capable of deliver- ing up to 1000 watts of peak power, depending on the load. The filtration zone is not current limiting and will deliver as much power as a 15 amp wall socket can provide.

All settings in the P1000 are non-volatile. Any changes made to the settings will not be lost, even if the P1000 is disconnected from AC power.

message continues to appear, please contact your dealer for additional service.

How do I reset the settings to factory default? The P1000 was designed to easily reset the micro- processor back to the original factory default. If the P1000 is displaying any characters in the front panel that seem abnormal, if the front panel buttons do not correlate with the display read-outs or to simply reset all settings back to the factory defaults follow these instructions.

With the unit powered off, hold down both Mode buttons (Up and Down) and press the Power button. This will activate the Setup Display Mode. Using the Mode Up or Down buttons, cycle to the “RESET” mode. Press either Edit button (Up or Down) and the display will read “GO ->” to confirm the choice. Press either Edit button again to perform the reset function. Once it is complete, the P1000 will exit the Setup Display Mode automatically.

Specifications

Output:
Power	-	up to 1000 Watts
Voltage	-	95-250 Volts
		(depending on model)
Current	-	7 Amps
Frequency	-	50-120 Hz
Peak	-	10 Amps (soft limit)
Distortion (THD+N)	-	0.1%
Input:
AC input range	-	90-250 Volts
		(depending on model)
Frequency input	-	50/60 Hz
		(depending on model)

Inside the U.S. and Canada

PS Audio’s warranty is 3 years parts and labor, from the date of original purchase. The warranty follows the product itself regardless of ownership, new or used.

Outside the U.S. and Canada

PS Audio has authorized distribution in many coun- tries of the world. In each country, the authorized importing retailer or distributor has accepted the responsibility for warranty of products sold by that retailer or distributor. Warranty service should nor- mally be obtained from the importing retailer or distributor from whom you purchased the product. In the unlikely event of service required beyond the capability of the importer, PS Audio will fulfill the conditions of the warranty. Such product must be returned at the owner’s expense to the PS Audio factory. Contact your PS Audio distributor or the PS Audio customer service department for more infor- mation.

Service issues

Should your unit ever require service or if you have any technical questions about the P1000, you must either contact your dealer (PS Audio if purchased direct) or your PS Audio distributor. No equipment will be received at our service facilities without an attached RA number.

If purchased through an authorized PS Audio dealer or distributor, the RA number must be obtained by the dealer or distributor. If the product was purchased from PS Audio direct, this can easily be obtained by calling PS Audio at 720-406-8946or by contacting us via E-mail at <service@psaudio.com>.

When replacement parts are required, be sure they are specified by the manufac- turer to have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

Input capacity	-	750 VA
Power consumption -		35 Watts
(with no load)
General:
W x H x D	-	17 x 9 x 20 in
Weight	-	87 lbs (unboxed)
Cooling system	-	massive heatsinking

Do not operate with faulty or frayed power cables.

2

11