MONO OPERATION

Connecting to standard AC power

After making all other connections, set the POWER switch to OFF position. Then connect the power cord to a standard

SWITCH IN “MONO” POSITION

CH 2

MONO SIGNAL SOURCE

CH 1

USE CHANNEL 1 INPUT ONLY

AC outlet.

Mounting the amplifier

This amplifier is designed to accept standard rack mounting installations. Two slots on each end of the front panel make it suitable for such an installation.

Tightly secure four mounting screws (not supplied) through these fours slots and into your standard electronics equipment rack.

Turning the amplifier on

1.Turn on the audio input source equipment which is connected to the amplifier INPUT jacks.

2.Set the amplifier’s Channel 1 and Channel 2 output level gain controls to the minimum level settings.

3.Push in the power switch to turn the amplifier on.

CAUTION! Do not use balanced and unbalanced inputs simultaneously!!

Bridged Mode Operation

This amplifier can operate in a mono bridged output mode, if your speakers can handle the following power output levels:

XPA-100:

1000 watts

XPA-200:

1600 watts

XPA-300:

2000 watts

As shown in the diagram below, connect the speaker's positive

(+)to the amplifier's red speakers left (1/2) terminals and negative (-) to red speakers right (1/2) terminals.

The speaker right (+) on the amplifier is used as a negative (-) terminal for a bridged connection.

NOTE: The extra amplifier output of 6.35mm phone jacks can not be used for the bridged connection. It can only be used in normal (non-bridged) operation as a stereo speaker output.

MONO BRIDGED OPERATION

SWITCH IN “BRIDGED” POSITION

DO NOT USE

BLACK TERMINALS

USE

MONO SIGNAL SOURCE

CHANNEL 1

 

 

 

 

 

INPUT ONLY

 

 

 

 

 

CAUTION! Do not use balanced and unbalanced inputs simultaneously!!

Using the power LED meters

The meter pointer position indicates the amplifier output power. For ease of reading in dark environments, the meter is illuminated.

Using the Channel 1 and Channel 2 Output Level controls Rotate output level gain clockwise to increase, or counter- clockwise to decrease the output power. To get the best performance with the least sound distortion, always adjust the output level gain so the meter's pointer does not continuously exceed the extreme right of the meter's scale.

CAUTION: It is possible to overdrive the amplifier by setting output level gain too high, which may cause damage or failure.

About the internal protect circuitry

Special clip circuitry incorporated into your PYRAMID XPA amplifier’s design protects the amplifier and speaker system from being damaged from overdriving power.

Under normal conditions, the amplifier’s clip indicator will flicker as the output power momentarily exceeds the level as set by the output level gain selector.

However, under excessive output conditions, the protect indicator lights remain on continuously, alerting you that the special clip circuitry has become active. When this occurs, you should simply reduce the output power level by rotating the Master Volume control counterclockwise.

3-PYRAMID XPA-100/XPA-200/XPA-300 Amplifier Owner’s Manual

PYRAMID XPA-100/XPA-200/XPA-300 Amplifier Owner’s Manual-4

Page 3
Image 3
Pyramid Car Audio XPA-200, XPA-100 manual Connecting to standard AC power, Mounting the amplifier, Turning the amplifier on

XPA-200, XPA-100 specifications

Pyramid Car Audio is renowned for delivering high-quality audio products that enhance the driving experience. Among its extensive lineup, the Pyramid XPA-200 and XPA-100 amplifiers stand out as impressive options for car audio enthusiasts looking to upgrade their sound systems.

The Pyramid XPA-200 is a powerful 2-channel amplifier designed to provide robust sound performance. It boasts a peak power output of 2000 watts, ensuring that users can enjoy clear and dynamic audio, even at high volumes. One of the key features of the XPA-200 is its built-in low-pass filter, which allows users to control the frequency range of the bass, ensuring a tight and accurate low-end response. This feature is particularly beneficial for those who enjoy deep bass without muddying the overall sound quality. Additionally, the XPA-200 includes a variable gain control that helps users adjust the audio input to match the specifications of their car audio system.

On the other hand, the Pyramid XPA-100 offers a more compact solution, delivering 1000 watts of peak power in a single-channel configuration. This amplifier is ideal for those looking to drive a subwoofer while maintaining space in their vehicle. The XPA-100 also features a built-in low-pass filter and gain control, providing users with the flexibility to tailor their sound to their preferences. Its compact design makes it easy to install in smaller vehicles or tighter audio setups without sacrificing sound quality.

Both amplifiers utilize advanced circuitry to minimize distortion, allowing for a cleaner sound reproduction across all frequencies. They are equipped with short circuit protection and thermal protection to ensure safety during operation, enhancing their reliability for long-term use. The stylish and durable chassis of each model not only contributes to their aesthetic appeal but also aids in heat dissipation, ensuring that the amplifiers operate efficiently even during extended periods of use.

In summary, the Pyramid XPA-200 and XPA-100 amplifiers are exceptional choices for users looking to elevate their car audio experience. With their powerful output, innovative features, and reliable performance, these amplifiers cater to the needs of both casual listeners and hardcore audiophiles alike. Whether you are looking to add depth to your music or enhance the clarity of your sound system, Pyramid Car Audio's XPA series offers an array of options to suit your audio needs.