Python 091-0593 owner manual SAfETY Precautions Read BEfORE Using, Symbol Usage

SECTION 1 – SAfETY PRECAUTIONS - READ BEfORE USING

1-1. Symbol Usage

Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols.

�Marks a special safety message.

�Means “Note”; not safety related.

1-2. Arc Welding Hazards

�The symbols shown below are used throughout this manual to call attention to and identify possible hazards. When you see the symbol, watch out, and follow the related instructions to avoid the hazard. The safety information given below is only a summary of the more complete safety information found in the Safety Standards listed in Section 1-4. Read and follow all Safety Standards.

�Only qualified persons should install, operate, maintain, and repair this unit.

�During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks or severe burns. The electrode and work circuit is electrically live whenever the output is on. The input power circuit and machine internal circuits are also

live when power is on. In semiautomatic or automatic wire welding, the wire, wire reel, drive roll housing, and all metal parts touching the welding wire are electrically live. Incorrectly installed or improperly grounded equipment is a hazard.

�Do not touch live electrical parts.

�Wear dry, hole-free insulating gloves and body protection.

�Insulate yourself from work and ground using dry insulating mats or covers big enough to prevent any physical contact with the work or ground.

�Do not use AC output in damp areas, if movement is confined, or if there is a danger of falling.

�Use AC output ONLY if required for the welding process.

�If AC output is required, use remote output control if present on unit.

�Disconnect input power or stop engine before installing or servicing this equipment. Lockout/tagout input power according to OSHA 29 CFR 1910.147 (see Safety Standards).

�Properly install and ground this equipment according to its Owner’s Manual and national, state, and local codes.

�Always verify the supply ground – check and be sure that input power cord ground wire is properly connected to ground terminal in disconnect box or that cord plug is connected to a properly grounded receptacle outlet.

�When making input connections, attach proper grounding conduc- tor first – double-check connections.

�Frequently inspect input power cord for damage or bare wiring – replace cord immediately if damaged – bare wiring can kill.

�Turn off all equipment when not in use.

�Do not use worn, damaged, undersized, or poorly spliced cables.

�Do not drape cables over your body.

som _nd_7/02

This group of symbols means Warning! Watch Out! possible ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the hazards.

�If earth grounding of the workpiece is required, ground it directly with a separate cable.

�Do not touch electrode if you are in contact with the work, ground, or another electrode from a different machine.

�Use only well-maintained equipment. Repair or replace damaged parts at once. Maintain unit according to manual.

�Wear a safety harness if working above floor level.

�Keep all panels and covers securely in place.

�Clamp work cable with good metal-to-metal contact to workpiece or worktable as near the weld as practical.

�Insulate work clamp when not connected to workpiece to prevent contact with any metal object.

�Do not connect more than one electrode or work cable to any single weld output terminal.

SIGNIfICANT DC VOLTAGE exists after removal of input power on inverters.

�Turn Off inverter, disconnect input power, and discharge input capacitors according to instructions in Maintenance Section before touching any parts.

fUMES AND GASES can be hazardous.

Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health.

�Keep your head out of the fumes. Do not breathe the fumes.

�If inside, ventilate the area and/or use exhaust at the arc to remove welding fumes and gases.

�If ventilation is poor, use an approved air-supplied respirator.

�Read the Material Safety Data Sheets (MSDSs) and the manufacturer’s instructions for metals, consumables, coatings, cleaners, and degreasers.

�Work in a confined space only if it is well ventilated, or while wearing an air-supplied respirator. Always have a trained watch- person nearby. Welding fumes and gases can displace air and lower the oxygen level causing injury or death. Be sure the breath- ing air is safe.

�Do not weld in locations near degreasing, cleaning, or spraying op- erations. The heat and rays of the arc can react with vapors to form highly toxic and irritating gases.

�Do not weld on coated metals, such as galvanized, lead, or cadmium plated steel, unless the coating is removed from the weld area, the area is well ventilated, and if necessary, while wearing an air-supplied respirator. The coatings and any metals containing these elements can give off toxic fumes if welded.

OM-1594 Page 1

Millermatic Python® Owner's Manual Page