DCM
Specifications
The QSC DCM acts as the interface between a cinema film audio processor and the power amplifiers in a
Dimensions (HWD):
Line Voltage Requirements: Accessories Included:
Front Panel Controls
Power Switch:
Monitor Mode Select:
Monitor Channel Select:
Monitor Volume:
Test Lead Connections:
Bypass Mode Select Switch:
Diagnostics Button:
Indicators:
Power Indicator:
Monitor Mode Indicators:
Processor Channel Indicators:
Amplifier Channel Indicators:
Load Fault Indicator:
Clip Indicator:
Rear Panel Controls
Bypass Crossover Level:
Surround EX Mode Switch:
Rear Panel Control Connectors:
Input:
Amplifier DataPorts:
RS232 Serial Port:
Powered Sub/Hearing:
Impaired Output:
Surround EX Insert Point:
AC Power Inlet:
DCM Inputs
Screen Channels and Subwoofer: Input Stage Type:
Input Impedance:
Maximum Input Level (Screen channels):
Maximum Input Level (Subwoofer channels):
A/D Conversion (Screen channels only):
Surround Channels:
Dataport Outputs
Screen Channels:
Output Attenuation Steps:
Dynamic Range:
THD+N 20
Input Level, All Filters Flat:
Frequency Response:
D/A Conversion:
Filter Topology:
Specifications subject to change without notice.
Crossover Filters: | ||
| programmable in approx. 1 Hz steps from | |
| 150 Hz - 15 kHz |
|
Parametric EQ: | Digital bandpass constant Q filter with ±10 dB | |
| of boost/cut programmable in approx. 1/10 octave | |
| steps from 80 Hz | |
| in 1/10th octave steps from 1/10 to 2 octaves. | |
CD Horn EQ: | Available on high frequency outputs only | |
Screen EQ: | Available on high frequency outputs only | |
Delay: | Programmable in 21 µs steps from 0 to 21 ms | |
| per output |
|
Polarity: | Normal, Inverted |
|
Mute: | Individual mutes on each screen channel output | |
Subwoofer: |
|
|
Output Stage Type: | Single ended (balanced impedance) | |
Output Attenuation Steps: | 0 dB to | |
Dynamic Range: | 99 dB |
|
THD+N 20 |
|
|
Input Level, All Filters Flat: | 0.02% |
|
Filter Topology: | Digitally controlled analog on | |
| DSP on |
|
High Pass Filter: | ||
| programmed as 0.707 or 2, flat or | |
| operation |
|
Mute: | One mute for all subwoofer outputs | |
Surround Channels: | Hardwire | |
| Surround Insert |
|
Output Channels (using the |
|
|
Surround Insert connector): | 2 or 3 selectable on rear panel | |
Amplifier A.C. Control |
|
|
all amps power on with DCM activation |
|
|
Emergency Bypass Crossover |
|
|
Filter Type: | 1st order Butterworth, 2 or 3 way | |
Attenuation Range (trimpot): |
| |
Powered Subwoofer Output |
|
|
Output Stage Type: | Single ended (balanced impedance) | |
Output Impedance: | 50Ω |
|
Maximum Output Level: | +14.2 dBu (4.0 Vrms) | |
Loading Requirements (total of |
|
|
remote & dataport connection): | RMIN = 2k ohms | CMAX = 4 nF |
Hearing Impaired Output |
|
|
Output Stage Type: | Single ended (balanced impedance) | |
Output Impedance: | 50Ω |
|
Nominal Output Level: | ||
Loading Requirements: | RMIN = 2k ohms | CMAX = 4 nF |
Surround Insert I / O |
|
|
Output Stage Type: | Hardwired connection to processor | |
| input connector |
|
Input Stage Type: | Hardwired connection to DataPort | |
| output connector |
|
Monitor Speaker |
|
|
Dimensions: | ||
Amplifier Output Power: | 10 watt class AB amplifier | |
Frequency Response: | 100 Hz – 8 kHz (±2 dB) | |
Dynamic Processing: | 1.5:1 compression |
1675 MacArthur Boulevard • Costa Mesa, CA 92626 • Ph: | qscaudio.com |
DCM Spec Sheet - 02/23/06