RAD Data comm ASM-60 2. Operating ASM-60 , 3. Configuring ASM-60

Quick Start Guide ASM-60 Installation and Operation Manual

2 Configuring ASM-60

2. Operating ASM-60

Normal Indications

The table below shows the correct status of the indicators a few seconds after

power-up.

Indicator Status

PWR ON

TD Depends on DTE data transmission

RD Depends on DTE data transmission

RTS Depends on DTE RTS signal status

DCD Depends on remote modem data transmission

TEST OFF

ALM OFF

SYNC A/SYNC B Green or red, depending on remote modem data

transmission

3. Configuring ASM-60

Configure ASM-60 to the desired operation mode via an ASCII terminal using the

embedded management software. Configuration of the ASM-60 modem includes

selection of a data rate.

Selecting the Data Rate

 To select the data rate:

1. From the Configuration menu, type 1.

The Data Rate menu appears.

2. Select the data rate by typing the number corresponding to the desired value

and then type 2 to save the changes.

Main Menu

↓ 1

Configuration

↓ 1

Data Rate

Contents

Main Page ASM-60 4-Wire Symmetrical VDSL Modem Installation and Operation Manual Notice Limited Warranty General Safety Instructions Safety Symbols Handling Energized Products General Safety Practices Connection of AC Mains Connection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility (EMC) FCC-15 User Information Attention Canadian Emission Requirements Warning per EN 55022 (CISPR-22) Page Declaration of Conformity Page Quick Start Guide 1. Installing ASM-60 Setting the Internal Switches Connecting the Interfaces Connecting the Power 2. Operating ASM-60 Normal Indications 3. Configuring ASM-60 Selecting the Data Rate Contents Page List of Figures List of Tables Page Chapter 1 Introduction 1.1 Overview Versions Application Features DTE Interface Management Test Capabilities Real Time Alarms 1.2 Physical Description 1.3 Functional Description 1.4 Technical Specifications Page Chapter 2 Installation and Setup 2.1 Site Requirements and Prerequisites 2.2 Package Contents 2.3 Installation and Setup Performing the Internal Settings Opening the ASM-60 Case Closing the ASM-60 Case Connecting the Interfaces Connecting the Line Connecting the DTE Connecting the Power Page Chapter 3 Operation 3.1 Front Panel Indicators 3.2 Operating ASM-60 Turning On ASM-60 Normal Operation Normal Indications Turning Off ASM-60 Chapter 4 Management from a Terminal 4.1 Preparing for the Control Session Control Port Interface Characteristics Preparing Terminal Control Port Handshaking Protocol 4.2 Navigating the Management Menus Terminal Management Menus 4.3 Starting the Control Session 4.4 Configuring ASM-60 Selecting the Data Rate 4.5 Displaying the ASM-60 System Information Displaying the ASM-60 Status 4.6 Resetting ASM-60 Page Chapter 5 Diagnostics 5.1 Error Detection Power-Up Self-Test Front-Panel LEDs Alarms Working with the Log File Table 5-1. ASM-60 Alarms 5.2 Displaying the VDSL Performance Diagnostics ASM-60 has capabilities for collection of the VDSL performance diagnostics. Figure 5-3. VDSL Performance Screen Table 5-2. ASM-60 Performance Monitoring Parameters 5.3 Running the Diagnostic Tests Running the LEDs Test Page Appendix A IR-ETH Interface Module A.1 IR-ETH Connector Options A.2 Technical Specifications General LAN WAN A.3 Installation and Operation DIP Switch Settings LED Indicators Connecting to LAN Appendix B IR-ETH/QH Interface Module B.1 Introduction B.2 IR-ETH/QH Connector B.3 Technical Specifications B.4 Installation and Operation Setting the DIP Switch LED Indicators Connecting the LAN Appendix C IR-IP Interface Module C.1 Introduction Overview Application C.2 Technical Specifications Router LAN WAN C.3 Physical Description IR-IP LEDs IR-IP DIP Switch C.4 IR-IP Management Subsystem, General Introduction Accessing the IR-IP Management Subsystem Default IP Communication Parameters C.5 Performing Preliminary Configuration General Outline of Preliminary Configuration Connecting the Telnet Host Preliminary Telnet Host Configuration Assigning the Router LAN Interface Address IP Learning Mechanism Assigning a LAN IP Address to a New IR-IP Changing the LAN IP Address of a Configured IR-IP What to Do If ... C.6 IR-IP Management Utility General Operating Procedures Starting a Management Utility Appendix C IR-IP Interface Module ASM-60 Installation and Operation Manual C-10 Quick Setup Menu C.7 Quick Setup Menu To access the Quick Setup menu: From the Main menu, type 1. The Quick Setup menu appears (Figure C-6). LAN IP Address LAN IP Mask WAN IP Address Read Protocol from DIP Switches Protocol C.8 Management Access Menu Telnet Password Telnet Inactivity Timeout C.9 Advanced Setup Menu Device Identification Menu Device Name Contact Person System Location Interface Parameters Menu LAN Status WAN Status WAN Throttle Aging Timeout WAN Protocol Parameters Frame Relay Protocol Menu Self Learn Maintenance Protocol DLCI CIR WAN Protocol Parameters PPP Protocol Menu Header and Control Field Compression Protocol Field Compression Authentication Protocol Security Host/Guest User Name To Send Password To Send User Name To Accept Password To Accept Multicast IP Menu Multicast Forwarding Static Groups C.10 Device Control Menu New Software Download Menu Server IP Address File Name Total Timeout Start Operation View Error Log Screen Resets Menu Reset Device Reset LAN Reset WAN C.11 View Menu Configuration and Connection ARP Tables Multicast Groups Table Screen Statistics Screen Figure C-24. WAN Statistics Screen C.12 Diagnostic Tool (Ping Terminal) Menu Figure C-25. Diagnostic Tools Menu This section provides information on the diagnostic tool provided with IR-IP (the ping utility). In the Main menu, type 6. The Diagnostic Tools menu appears (Figure C-25). Using the Ping Function C.13 Erasing Users Configuration C.14 Erasing IR-IP Software Erasing Application Software Downloading New Software Page Customer Response Form Page Error Report