Radio Shack 15-2127 owner manual +056#..+0 $#664+5, 2414#//+06* 4/16, R9#40+0R

5/KP/3"7PKXGTUCN"4GOQVG"%QPVTQN"L")QNHDCI"5V[NG

15-2127 OWNER’S MANUAL — Please read before using this equipment.

#"+/2146#06"#

If an icon appears at the end of a paragraph, go to the box on that page with the corresponding icon for pertinent information.

Rý— Warning	° — Hint
. — Caution	± — Note
# — Important

R"9#40+0)"R"

Thank you for purchasing the RadioShack 3-in-1 Universal Remote Control – Golfbag Style. It is a state-of-the-art device specially designed to operate the major functions of your television (TV), video cassette recorder (VCR), and cable converter (CBL). It is compatible with most popular brand TV, VCR, and CBL devices. The remote is pre-programmed before you purchase it. Input the correct code for your device and the remote is ready to use.

SET — Initiates		PWR — Turns the selected
programming mode.		device on or off.
TV/VCR —
Switches the
view between
the TV and VCR.		TV/VCR/CBL — Selects the
VOL+/VOL– Adjusts
		desired device type.
the volume.
		ENTER — Press after entering
Battery Compartment		channel numbers (on some TV
RESET — Resets stored		models).
		CH+/CH– Selects a channel.
remote settings.
J — Play
# — Rewind		MUTE — Turns the sound on
		or off.
ç — Record	' — Stop	, — Fast Forward

f— Pause

Dispose of batteries promptly and properly.

."%#76+10".

•Use only fresh batteries of the required size and recommended type.

•Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities.

•If you do no plan to use the remote control for a month or longer, remove the batteries.

•Rechargeable batteries are to be removed from the remote before being charged.

•Rechargeable batteries are only to be charged under adult supervision.

•Batteries are to be inserted with the correct polarity.

•Do not short-circuit the terminals.

•Do not attempt to charge non-rechargeable batteries.

±"016'"±"

Installing Batteries

When the remote stops operating properly, replace the batteries within 10 minutes of removing the old batteries. Otherwise, the programmed settings and codes will be lost.

Programming the Remote

If the device does not turn off, repeat steps 3–5, using another code from the Code List for your device until you find one that works.

+056#..+0)" $#66'4+'5

Your remote requires two AA batteries (not supplied) for power. For the best performance and longest life, we recommend RadioShack alkaline batteries.Rý.

1.Unseal the flap on the remote, then pull out the battery compartment.

2.Use a Phillips screwdriver to loosen the screw on the battery compartment cover, then remove the cover.

3.Place two AA alkaline batteries in the compartment as indicated by the polarity symbols (+ and –) marked inside.

4.Replace the cover and secure it with the screw.

5.Replace the battery compartment and seal the flap. ±

241)4#//+0)"6*'" 4'/16'

While programming, make sure to aim the remote at the device and that the distance between the remote and device is within 21 feet (7 meters).

1.Refer to the “Code List” on Page 3 and write down the codes for your device.

2.Manually turn on your TV, VCR, or cable converter.

3.Press TV, VCR, or CBL to select the desired device type. The red LED blinks once.

4.Hold down SET until the red LED blinks twice.

5.Enter the 4-digit code. If the code is valid, the red LED blinks twice.

6.Aim the remote control at the device

and press PWR. The device should turn off. ±

© 2002 RadioShack Corporation.

All Rights Reserved.

RadioShack and RadioShack.com are trademarks

used by RadioShack Corporation.