±"016'"±"
The transmitter’s channel setting must be the same as the receiver setting. If the door chime occasionally sounds without anyone pressing BELL, this indicates that the channel settings are different. Change the channel settings so both the transmitter and the receiver match.
±"016'"±"
•Press BELL until the indicator lights. Otherwise, the receiver may not work properly.
•If you don't want to be bothered by the door chime, slide ON/OFF on the receiver to OFF.
Limited One-Year Warranty
This product is warranted by RadioShack against manufactur- ing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchi- sees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURA- TION OF THE WRITTEN LIMITED WARRANTIES CON- TAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSI-
BILITY TO CUSTOMER OR ANY OTHER PERSON OR EN- TITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM IN- CONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REV- ENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclu- sions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the same or similar design; or
(c)refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, im- proper or abnormal usage, failure to follow instructions, im- proper installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those provided by a RadioShack Authorized Ser- vice Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-up ser- vice adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RadioShack Customer Relations, 200 Taylor Street, 6th Floor,
Fort Worth, TX 76102
12/99
3.Install three AAA batteries as indicated by the polarity symbols (+ and –) marked inside.
4.Replace the compartment door.
5.Repeat Steps 1-4 for the other transmitter. If the transmitter's LED indicator dims, replace its batteries.
+0"6*'"4'%'+8'4
1.Slide the receiver's battery compartment door in the direction of the arrow to remove it.
2.There are two channel switches inside the battery compartment — BELL 1 and BELL 2. Slide the channel switches so
that they are on the same channel as the transmitter. ±
3.Install three C size batteries as indicated by the polarity symbols (+ and –) marked inside the compartment.
4.Replace the compartment door. If the receiver's LED flashes with a short beep tone, replace its batteries.
12'4#6+10
1.Slide ON/OFF on the receiver to ON.
2.Press and hold down BELL on the BELL 1 transmitter. Transmit begins, the
indicator lights, and the receiver sounds the door chime twice. ±
3.When BELL is pressed on the BELL 2 transmitter, it’s indicator lights and the door chime sounds “Home sweet home”.
75+0)"6*'"%*+/'"#5"#0" '064;"%*+/'
1.Connect the transmitter to a normally open alarm sensor. You need 2- conductor wire (not supplied) to make this connection.
2.Split the ends of the wire, then connect the wire from the sensor's switch to the screw holes on the back of the transmitter, using the two supplied machine screws. If the sensor you are using has both normally open and normally closed contacts, be sure to connect to the sensor's normally open contacts.
3.Slide ON/OFF on the receiver to ON.
6*'"(%%"9#065";17" 61"-019
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Consult your local RadioShack store or an experienced radio/TV technician for help.
•If you cannot eliminate the interference, the FCC requires that you stop using your door chime.
Changes or modifications not expressly approved by RadioShack may cause interference and void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
52'%+(+%#6+105
| | |
Frequency | 433.92 MHz ± 600KHz |
Transmitter current consumption | <10mA |
Receiver current consumption...<2mA @ standby
<130mA @ sound playing Receiver battery low.......................... 2.4V ± 0.1V
Receiver audio power............... > 80dBA @ 25cm Transmitter operating
temperature | –20°C to 60 °C |
| (–4°F to 140°F) |
Specifications are typical; individual units might vary. Specifications are subject to change without notice.
