±"016'"±"
•When the switch is at ALM 1 + ALM 2 position, alarm setting is not available
•Press ALARM/SET at any time to view the set alarm time according to the alarm switch position ALM 1 or ALM 2.
hold) MIN until the desired minute appears.
3. Release TIME SET, the set time appears.
5+)0#."564'0)6*"&'6'%6+10"
U0&& appears when the clock receives a signal. The digit left of the colon indicates the level of signal strength.
5KIPCN"+PFKECVQT | 5KIPCN"5VTGPIVJ |
|
|
Blank | No signal |
|
|
Single bar | Weak |
Double bar | Medium |
|
|
Triple bar | Strong |
|
|
Place your clock in a location with strong signal strength. It is recommended to locate the clock near a window facing the direction of Fort Collins, Colorado. If the clock has poor signal reception or unstable signal marks, move the clock to another location.
While the clock is receiving, press TIME SET once to go to the Time display mode. The clock continues receiving the atomic time. Press HOUR/WAVE to enter Signal Strength display.
While the clock is receiving, if you set the time or an alarm, the clock stops receiving immediately.
When receiving cannot be completed at 7 minutes after power up, the clock returns to the time display with clock '(0&- am appears and remote control (RC) receiving continues.
4'%'+8+0)"619'4"+0&+%#614"
6QYGT"+PFKECVQT | +PFKECVGU | |
|
| |
Blinking | The clock is receiving | |
|
| |
Static On | Successful reception | |
Off | No reception/failed | |
reception | ||
| ||
|
|
(+456"4'%'26+10"#(6'4" %100'%6+0)"219'4
The clock starts to search for the WWVB signal and searches for 20 minutes after you connect it to power.
In optimal conditions, the correct time will be displayed within 10 minutes
The atomic reception tower icon will keep blinking when the clock is receiving the signal.
The static atomic reception tower indicator indicates successful reception.
The signal is at its maximum strength from 12:00 am to 3:00 am and with minimal radio
interference. In most cases, the clock will not receive and update its time until this time.
9KVJKP"VJG"HKTUV"5"JQWTU
If your clock fails to receive the signal in the 1st reception after
#HVGT"VJG"HKTUV"5"JQWTU"
If no signal can be received within the first three hours, the clock repeats the reception every three hours until it receives a signal.
#WVQOCVKE"VKOG"WRFCVG
The clock automatically updates everyday at 01:00 (1:00 a.m.) and 03:00 (3:00 a.m.) and 05:00 (5:00 a.m.). If the automatic time update fails, it will repeat the update every 3 hours until it is successful in receiving the signal.
/CPWCN"VKOG"WRFCVG
Manual reception can be started anytime by pressing HOUR / WAVE.
The time display changes to Signal Strength Detection display U0&&U . The clock will start to search for the WWVB signal for 20 minutes.
5'66+0)"6*'"#.#4/5
#.#4/"3"14"4
1.Slide ALM to ALM 1 or ALM 2. The ALM 1 LED lights or the ALM 2 LED lights. ±
2.To set the alarm hour, Press and hold ALARM/SET and press (or press and hold) HOUR/WAVE until the desired hour appears on the display.
3.To set alarm minute, press and hold ALARM/SET and press (or press and hold) MIN until the desired minute appears on the display.
4.Release ALARM/SET, the clock returns to the set time display.
75+0)"6*'"#.#4/"
To activate Alarm 1 only, slide ALM to ALM 1, then slide ALARM/ON/OFF located on the back of the clock to ON, or ...
to activate Alarm 2 only, slide ALM to ALM 2,
then slidelocated on the back of the clock to ON, or ...
to activate both Alarm 1 and Alarm 2, slide ALM to ALM 1 + ALM 2, then slide ALARM ON/ OFF located on the back of the clock to ON.
2
