Preparation for Use
Setup
Turn on the Unit for the First Time
VCR
VCR
1
Turn on the TV and set it to channel 3.
•If channel 3 is already occupied for broadcasting, see“RF Output Channel” section on page 6.
•If your antenna is connected to an antenna ampli- fier, the amplifier’s gain adjustment may need to be temporarily reduced in order for
2 | POWER | Remote Control | TV Screen |
|
| LANGUAGE SELECT | |
|
| B ENGLISH | [ON] |
|
| FRANCAIS | |
ESPAÑOL
or
3 | CH 01 |
| AUTO SET UP |
Do you connect the cable from the cable box or the satellite box to the unit’s
YES
Yes Press [MENU]
to exit.
• Refer to “Hint for Cable Box or
Satellite Box” section on page 6. NO
No Please wait for a few minutes.
After scanning...
To Add or Delete Channels
1)Press [MENU] until the main menu appears.
2)Select “CHANNEL SET UP” by pressing [K/L]. Then, press [B].
3)Select “MANUAL SET UP” by pressing [K/L]. Then, press [B].
4)Enter the desired channel number by pressing [K/L] or
[SKIP/CH. G/K H/L].
5)Add or Delete it from memory by pressing [s/B] so that “ADD” or “DELETE” flashes on the TV screen accordingly.
6)Exit the Preset mode by pressing [CLEAR/C.RESET].
To Preset the Channel Again
1)Press [MENU] until the main menu appears.
2)Select “CHANNEL SET UP” by pressing [K/L], then press [B].
3)Select “AUTO SET UP” by using [K/L], then press [B]. After scanning, the tuner stops on the lowest memorized channel.
To Change the On-Screen Language
1)Press [MENU] until the main menu appears.
2)Select “LANGUAGE SELECT” by pressing [K/L], then press [B].
3)Select “ENGLISH” , “FRANCAIS” or “ESPAÑOL” by pressing [K/L] , then press [CLEAR/C.RESET] to exit.
Hint
•If you accidentally select Spanish or French and need English: Press [MENU] and choose SELEC. IDIOMA or SELECTION LANGUE. Press [B] and select ENGLISH. Finally, press [CLEAR/C.RESET].
•To add or delete channels in this unit, [SKIP/CH. G/K H/L] button works on the channel number memorized in this unit, [K/L] works on all.
Clock Setup
VCR
VCR
3 |
| CLOCK SET | ||
| MONTH DAY | YEAR | ||
or | 1 0 | / 0 2 | – – – – | |
| HOUR MINUTE | AM/PM | ||
| – – | : – – | – – | |
| Select the current day. | |||
4 |
| CLOCK SET | ||
or | MONTH DAY | YEAR | ||
1 0 | / 0 2 | 2 0 0 6 | ||
| HOUR MINUTE | AM/PM | ||
| – – | : – – | – – | |
| Select the current year. | |||
5 |
| CLOCK SET | ||
or | MONTH DAY | YEAR | ||
1 0 | / 0 2 MON 2 0 0 6 | |||
| HOUR MINUTE | AM/PM | ||
| 0 5 | : – – | – – | |
| Select the current hour. | |||
6 |
| CLOCK SET | ||
or | MONTH DAY | YEAR | ||
1 0 | / 0 2 MON 2 0 0 6 | |||
| ||||
| HOUR MINUTE | AM/PM | ||
| 0 5 | : 4 0 | – – | |
| Select the current minute. | |||
7 |
| CLOCK SET | ||
| MONTH DAY | YEAR | ||
| 1 0 | / 0 2 MON 2 0 0 6 | ||
or | HOUR MINUTE | AM/PM | ||
| 0 5 | : 4 0 | P M AM | |
•The tuner stops on the lowest memorized channel.
•You can select only the channels memorized in this unit by using [SKIP/CH. G/K H/L] (or [CHANNEL K/L]).
•If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, press [B] once again.
Hint
•Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.
To Select a Channel
1MENU
or 
- M E N U -
TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP
BCLOCK SET LANGUAGE SELECT AUDIO OUT
TV STEREO [ON]
SAP
•If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2).
B PM |
Select “AM” or “PM”.
8To exit the CLOCK SET screen
Hint
You can select a channel by using the Number buttons or [SKIP/CH. G/K H/L].
Notes for using the Number buttons:
•When selecting cable channels which are higher than 99, enter channel numbers as a
•You must precede
2 |
| CLOCK SET | |
or | MONTH DAY | YEAR | |
1 0 | / – – | – – – – | |
| HOUR MINUTE | AM/PM | |
| – – | : – – | – – |
Select the current month.
•To go back one step, press [s] (during steps 2) to 7) ).
•Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds.
– 8 – | EN |
