RCA RS2655, RS2653 Display Settings, Remote Control, Showing Demonstration, Installing Batteries

DIMM 2

RS2653_55_EN(TCEC) 1/13/06 1:27 PM Page 8

	General Controls
EN	Remote Control
	— Turns power on or off from STANDBY mode.
	CD — Selects CD player.
	TUNER — Selects radio tuner and changes radio band in Tuner mode.
	TAPE — Selects tape player.
	AUX — Selects Aux mode; turns the system on.
	CD INFO — Selects among disc display information.
	B. BOOST—Turns Bass Boost on or off.
	DEMO/DIMMER —Turns the feature demonstration on or off; adjusts dis-
	play brightness;
	VOL+ / VOL- — Increases/ decreases volume.
	PLAY/PAUSE		— Plays and pauses current CD.
	NEXT	/FWD	— In CD mode - Skips forward to the next CD track;

Display Settings
Display	EN
Showing Demonstration	Note:
Press DIMMER•DEMO to turn on/off demonstration	The wake up timer source will be
	the source you are in when set-
mode. The demonstration scrolls through all display
	ting the timer.
operations.

In Tuner mode - Tunes up radio frequency.
PREV	/REV	— In CD mode - Skips backwards to the previous CD
track; In Tuner mode - Tunes down radio frequency.
OPEN/CLOSE — Opens and closes CD disc tray.
STOP — Stops playing CD.
REPEAT — Repeats a track, CD, or all CDs.
	— mutes and restores audio output.
	— Turns on/off random playback.
FM ST. — Switches between FM stereo and mono modes.
DISC SKIP — Skips to next CD.

INTRO — Turns INTRO mode on or off to play the first 10 seconds of each track.

DN•FOLDER/PRESET•UP — Selects previous / next tuner preset station and previous / next folder during mp3/WMA CD playback. SLEEP — Selects the time interval in minutes before the unit turns off.

Note:

Cassette functions can not be operat- ed from the remote control.

Installing Batteries

The remote control must be inserted with 2 “AAA” or “R3” or “UM 4” batteries prior to use. Follow the steps below to ensure correct installation.

1.Open the battery compartment door (located at the back of the remote control) by sliding the cover out.

2.Before inserting the batteries, observe the polarities (that is, + and -) of the battery then relate the polarities to the engraved diagram inside the battery compartment. Now insert the batteries.

3.After installation of the batteries, place the lit to cover the batteries. Lightly push it closed with a snap.

Display Clock / Timer

Setting the Clock

1.Press and hold CLOCK until the hour flashes on the display.

2.	Press DIGITAL TUNING	or	to set the
	hour and then press CLOCK to shift to minute
	digits.
3.	Press DIGITAL TUNING	or	to set the
	minute.

4.Press PROG•SET to save settings or STOP to quit setting.

Note:

When system is ON, you can press

CLOCK to display the current time for about 2 seconds.

Setting the Timer

1.Press and hold TIMER until ON (timer on time) appears with the hour flashing.

2.	For setting time, press DIGITAL TUNING			or
	to set the hour and then press TIMER to shift
	to the minute digits.
3.	Press DIGITAL TUNING	or	to set the
	minute.

4.Press TIMER to change to OF (timer off time) with hour flashing. Repeat steps 2 & 3 for timer off time setting.

5.Press PROG•SET to save settings or STOP to quit setting.

Activating the Timer

Press and release TIMER to turn on/off the timer. The

timer is active when the clock icon is lit.

Adjusting the Display Brightness

1. Press and hold DIM- MER•DEMO for more than 2 seconds.

2.While the dimmer is displayed, press and

release DIMMER•DEMO repeatedly to select the desired level (DIMM 1 - 3).

Sleep Mode

You can select the time interval in minutes before the unit turns off automatically. Press SLEEP on the remote to select among OFF, 120, 90, 60, 45, 30, 15 and 5 minutes. (Remote Only)

The sleep icon flashes on the display when sleep mode is activated.

When sleep is activated, press SLEEP once to view remaining sleep time.

Press SLEEP again when the remaining sleep time is displayed to change sleep time.

Note:

Sleep is automatically de-activated when the unit is turned off.

4 5