Regency F1100S Step by Step Chimney Connector Installation, Leg and Bottom Shield Assembly

INSTALLATION

Leg and Bottom Shield Assembly

Bottom Shield
Small	850-121
Large	850-321
Legs (set of 4)
Steel - Painted Black	850-125
Cast - Painted Black	850-126
Cast - Gold Plated	850-127

The instructions below apply to the steel leg, painted cast leg and the gold plated cast leg. It will be easier to attach the legs to the stove if the stove is tipped on its back (preferably on a soft surface to prevent scratching). Ensure to be extremely careful when tipping stove.

1)Remove the 4 bolts from underside of the base of the pedestal and discard. Also remove cover plate and put to the side.

2)Place spacers in the 4 corners of the bottom heat shield and align with holes. If spacer does not fit, adjust flange with plyer.

3)Line up the heat shield with the bottom of the unit.

4)Start threading the bolt and washer (sup- plied with the bottom shield) for about 1/4 of the way through the leg with the wash- ers being underneath the legs. Ensure that the legs are properly aligned with heat shield and tighten the bolts.

STEP BY STEP

CHIMNEY AND

CONNECTOR

INSTALLATION:

Note: These are a generic set of chim- ney installation instructions. Al- ways follow the manufacturers own instructions explicitly. Check Table 1 on page 14 for the Mini- mum Recommended Flue Heights.

1)With your location already established, cut and frame the roof hole. It is recommended that no ceiling support member be cut for chimney and support box installation. If it is necessary to cut them, the members must be made structurally sound.

2)Install radiant shield and support from above.

3)Stack the insulated pipe onto your finish support to a minimum height of 3 feet above the roof penetration, or 2 feet above any point within 10 feet measured horizontally. There must be at least 3 feet of chimney above the roof level.

8)To complete your chimney installation, in- stall the double wall connector pipe from the stove’s flue collar to the chimney sup- port device.

9)If you are using a horizontal connector, the chimney connector should be as high as possible while still maintaining the 18" min- imum distance from the horizontal connec- tor to the ceiling.

10)NOTE: Residential Close Clearance and Alcove installations require a list- ed double wall connector from the stove collar to the ceiling level.

The diagrams below illustrate one way to install your unit into a standard ceiling or with a horizontal connector. Check with your dealer or installer for information on other options available to you.

5)Level the stove by adjusting the levelling bolts in the bottom of each leg.

6)Reinstall cover plate.

7)Install logo plate onto heat shield by placing in 2 holes as shown in diagram.

If you are installing outside combustion air, bend the tabs out 90 degrees. Pipe fresh air into the bottom shield by using a minimum 4" duct pipe with a mesh grill at the outside termination. Attach the pipe to the 2 tabs with screws.

Note: Increasing the chimney height above this minimum level will sometimes help your unit to “breathe” better by allowing a greater draft to be created. This greater draft can decrease prob- lems such as, difficult start-ups, back-smoking when door is open, and dirty glass. It might be suffi- cient to initially try with the mini- mum required height, and then if problems do arise add additional height at a later date.

4)Slide the roof flashing over your chimney and seal the flashing to the roof with roofing compound. Secure the flashing to your roof with nails or screws.

5)Place the storm collar over the flashing, sealing the joints with a silicone caulking.

6)Fasten the raincap with spark screens (if required) to the top of your chimney.

7)For optimum efficiency when installing into a masonry chimney, size accordingly, i.e. the 6" flue dia. is 28.28 sq.in.

Standard Ceiling Installation

Horizontal Installation

Regency Freestanding Woodstove 11