How To Use
Before using read the important safety instruction section in front of the manual.
Preparing the System
Cleaning solution:
1.Press the latch buttons on the sides of the
cleaning base and lift | 1 | |
the upper portion off | ||
| ||
the unit. You will |
| |
need to keep the |
| |
buttons pressed in |
| |
as you move the |
| |
upper portion away |
| |
| ||
from the base. The |
| |
2 | ||
cleaning solution | ||
tank is in the unit’s |
| |
bottom portion. |
|
2. Remove the filter |
| |
from the tank and |
| |
set aside. |
| |
| ||
3. Pour the bottle of |
| |
3 | ||
cleaning solution into | ||
| ||
the base of the unit |
| |
through the opening |
| |
where the filter was |
| |
removed. |
|
4.Place the filter back into its original position.
NOTE: It is important to make sure the filter is in place. The filter collects hair clippings and debris, and should be replaced along with the solution. Failure to do so will permanently clog the system rendering it inoperable.
5.Replace the top portion of the clean- ing base by lining up the three posts with the three holes in the tank. Push the top portion down until the two latches click into place.
6.You can dispose of the bottle and cap with your normal trash, or recycle where local ordinances apply.
Charging
Prior to using your shaver for the first time, put it on charge for 24 hours.
NOTE: It may take up to 3 cycles for the battery to reach full capacity.
Using Cleaning Base
Plug the power cord into the cleaning base and then into an electrical outlet.
Make sure arm is in the up position before inserting shaver. Push down to release arm. It will
Place the shaver into the unit, head side down, and slide its “tail” toward the “neck” of the base until it stops.
Push the arm down until it contacts the shaver (clicks into place).
Charging
Your shaver automatically begins to recharge as soon as it is in place in the cleaning base. While it is charging, the blue indicator light will flash; when it is fully charged the blue light will stop blinking and glow steadily.
Your Shaver can also be recharged by plugging it into the cord directly.
■Use only the charging adapter supplied with the shaver.
■Make sure your shaver is turned off.
■Connect the cord to the shaver, then plug the charging adapter into the electrical outlet. A charging indicator light will come on.
■Your shaver cannot be overcharged, so you can leave it plugged in and charging between shaves.
■To preserve the life of the batteries, let them fully run out every six months, then recharge them for
a full 24 hours.
■Cord/cordless rechargeable shavers can run directly off the cord if neces- sary. They will not recharge while you are shaving, so after shaving with the cord, turn the unit off and set it aside to charge. Cord/cordless shavers should not be used strictly as cord- operated shavers, as continued cord- only use will result in reduction of battery life.
■Quick Charge provides up to 60 min. of shaving after a
NOTE: If your shaver battery is com- pletely discharged or the shaver has not been used for a long time, the shaver may not start when operated using the cord. If this happens, charge the shaver for approximately five minutes before shaving.
NOTE: It may take up to 3 cycles for the battery to reach full capacity.
Operating the Cleaning System
Cleaning
To activate cleaning mode, simply press the CLEAN button on the cleaning base. The amber indicator light flashes through the entire cleaning cycle, which lasts approximately 2 minutes. When the clean- ing cycle has been completed, the amber light will stop blinking and glow steadily. The unit then returns to charging mode.
!Wait until the cleaning cycle has finished before removing the shaver from the base. If the shaver is removed during the cleaning cycle it will be covered with cleaning solution and be unusable.
Shaver should be left in cleaning base for 24 hours to allow it to dry for next usage.
Solution levels
The cleaning solution will slowly evapo- rate with use. When the solution levels get low, the red replacement indicator light will begin to flash. This means you have enough cleaning solution left for approximately 5 more cleanings. If the red light stops blinking and glows steadily, the unit will not operate until the solution and filter have been replaced.
Replacing the Filter and Solution Only Remington’s special cleaning solution and filter can be used with the Power Clean System. The cleaning solution contains a high percentage of alcohol and a special oil that lubricates your shaver each time it is cleaned. The filter is specially designed to collect hair debris yet allow for the system to clean your shaver.
Remove and discard filter and empty any remaining cleaning solution. Rinse unit tank then let dry. Fill with fresh solution, insert new filter and replace upper portion.
Wipe off the unit periodically with a damp cloth and remove any hair debris that has collected where the shaver sits.
8 | 9 |