Renesas M3028BT-EPB

M3028BT-EPB User’s Manual 3. Usage (Emulator Debugger)

REJ10J1459-0200 Rev.2.00 Sep 16, 2006

3.1.2 MCU Setting Dialog Box

MCU setting dialog box sets the information of the user system. It will be displayed after closing the Init dialog box.

When the tab settings of (1) to (3) have been finished, click “OK”.

(1) MCU tab

1. MCU setting

IMPORTANT

Notes on Selecting a Processor Mode:

z When the user system is connected, the level of pin CNVss of the MCU status should be "L". The MCU status

shows the pin level of the user system.

Specifying the processor mode

Select the appropriate processor mode that suits your

system. For this product, you can specify only the following

processor mode:

- Single-Chip Mode

Specifying the PM10 area (bit 0 of the

address 00005h)

Select this option when using the MCU in which the data

area access enable bit (PM10) is set to 1.

Page 47 of 86

Contents

Main M3028BT-EPB User's Manual Page Preface Important Page Precautions for Safety CAUTION Definitions of Signal Words IMPORTANT WARNING Page Contents Page User Registration Terminology 1. Outline 1.1 Package Components 1.2 Other Tool Products Required for Development 1.3 System Configuration Page Page 1.4 Specifications 1.5 Operating Environment 2. Setup 2.1 Flowchart of Starting Up the Emulator 2.2 Installing the Emulator Debugger 2.3 Connecting the Host Machine 2.4 Connecting the PC7501 2.5 Connecting the Power Supply for the Emulator 2.6 Turning ON the Power Page 2.7 Downloading Firmware M3028BT-EPB Users Manual 2. Setup REJ10J1459-0200 Rev.2.00 Sep 16, 2006 Page 28 of 86 2.8 Self-check Figure 2.6 Self-check procedure Page 2.9 Connecting the User System Page Page Page Page Page 2.10 A/D Conversion Bypass Capacitors 2.11 Selecting Clock Supply Page Page J1-4: GND J1-3: Oscillation output J1-2: GND J1-1: VCC Page 3. Usage (Emulator Debugger) 3.1 Starting Up the Emulator Debugger Page Page Page Page Page Page Page Page 3.2 Program Window Page M3028BT-EPB Users Manual 3. Usage (Emulator Debugger) REJ10J1459-0200 Rev.2.00 Sep 16, 2006 (3) Setting breakpoints 1. Screen after breakpoint setup Page 53 of 86 Breakpoint setup screen Page 3.3 Hardware Breakpoint Setting Window Page Page Page Page 3.4 Trace Window M3028BT-EPB Users Manual 3. Usage (Emulator Debugger) REJ10J1459-0200 Rev.2.00 Sep 16, 2006 3. Trace window (bus display) Page 61 of 86 Explanation of the trace window (bus display) 4. Trace window (disassemble display) Page Page 3.5 RAM Monitor Window 4. Hardware Specifications 4.1 Target MCU Specifications 4.2 Differences between the Actual MCU and Emulator Page 4.3 Connection Diagrams 4.4 External Dimensions 0.40 0.20 0.80 16.00 Max9.0 Min14.5 Page Page 4.5 Notes on Using This Product Page Page Page Page 5. Troubleshooting 5.1 Flowchart to Remedy the Troubles 5.2 When the Emulator Debugger Does Not Start Up Properly Page Page 5.3 How to Request for Support 6. Maintenance and Guarantee 6.1 User Registration 6.2 Maintenance 6.3 Guarantee 6.4 Repair Provisions 6.5 How to Make Request for Repair