Renesas M3062PT-EPB Note on Connecting the PC7501:

( 33 / 80 )

3.5 Connecting the PC7501

Figure 3.10 shows how to connect the PC7501 and the emulation probe.

Figure 3.10 Connecting the PC7501 and the emulation probe

CAUTION

Note on Connecting the PC7501:

•When connecting the emulation probe, be sure to hold the both sides of the emulation

probe horizontally and insert it directly.

•Always shut OFF power before connecting the emulation probe. Otherwise, internal

circuits may be damaged.

•The connectors of the M3062PT-EPB are guaranteed for only 50 insertion/removal

iterations.

M3T-FLX160-EPB

M3062PT-EPB

Contents

Main Page To use the product properly Precautions for Safety: Preface Contents Page Terminology Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION Page Page Page Note on NMI* Input: Note on RDY* Input: Note on HOLD* Input: Note on Clock Supply to the MCU: Notes on Maskable Interrupts: Notes on Reset Vector Area: Note on Accessing Address 00000h: Note on Access Prohibited Area: Notes on Stack Area: Note on Stop and Wait Modes: Note on Display of MCU Status: Note on Breaks: Notes on Address-Match Breaks: Notes on Address-Match Interrupts: Notes on Software Breaks: Note on Differences between the Actual MCU and Emulator: Note on the Watchdog Function: Note on DMA Transfer: Note on Protect Register: Notes on Internal Flash ROM of the MCU: Notes on Pullup Control: Note on Operating Frequency: Notes on Debugging in CPU Rewrite Mode: Chapter 2. Preparation 2.1 Package Components * For purchasing these products, contact your local distributor. 2.2 Other Tool Products Required for Development 2.3 Name of Each Part Page Note on Usage in Memory Expansion or Microprocessor Mode: Note on Accessing Address 00000h: Note on the Target Status POWER LED: Note on the Target Status CLOCK LED: 2.4 When Using the Emulator for the First Time Chapter 3. Setup 3.1 Selecting Clock Supply (1) Kinds of Oscillator Boards (2) Replacing an Oscillator Circuit Board Note on Replacing the Oscillator Circuit Board: Page Page 3.2 Switch Settings Note on Using the Internal Generator Circuit: 3.3 A-D Conversion Bypass Capacitors Note on the A-D Converter Function: 3.4 Pullup of Emulation Ports 3.5 Connecting the PC7501 Note on Connecting the PC7501: 3.6 Connecting the Target System Figure 3.11 shows how to connect this product according to your target system. Figure 3.11 Connecting the target system according to target systems Note on Connecting the Target System: Page Page Page Page * * Page * * Page Chapter 4. Usage 4.1 Turning On the Power Note on Memory Expansion or Microprocessor Mode: Note on the Target Status POWER LED: TARGET SYSTEM Note on the Target Status CLOCK LED: Note on Downloading Firmware: 4.3 Self-check Figure 4.3 LED displays in the self-check Page Chapter 5. Specifications 5.1 Specifications Table 5.1 Specifications of the M3062PT-EPB 5.2 Operation Timing of Memory Expansion Mode and Microprocessor Mode (5 V) (1) Separate Bus Timing -40 [ns] n: "3" for 3-wait Page -40 [ns] n: "2" for 2-wait (2) Multiplex Bus Timing *3 Calculated by the following formula according to the frequency of BCLK. -25 [ns] Page (3) Timing Requirements Tables 5.4 and Figure 5.3 list the timing requirements. Table 5.4 Timing requirements 5.3 Operation Timing of Memory Expansion Mode and Microprocessor Mode (3 V) (1) Separate Bus Timing -40 [ns] n: "3" for 3-wait Page (2) Multiplex Bus Timing *3 Calculated by the following formula according to the frequency of BCLK. -40 [ns] -50 [ns] n: "2" for 2-wait Page (3) Timing Requirements 5.4 Connection Diagram Table 5.8 Electrical characteristics of 74HC4066 Table 5.9 Electrical characteristics of port emulation EPGA Page Page Page Page Page 6.1 Flowchart to Remedy the Troubles Figure 6.1 Flowchart to remedy the troubles 6.2 When the Emulator Debugger Does Not Start Up Properly (1) When the LEDs of the PC7501 Shows an Error Table 6.1 Errors LEDs show and their checkpoints See the user's manual of the PC7501. See the CLK command of the emulator (2) MCU Setting Dialog Box Does Not Appear at Debugger Startup (target connected) Table 6.2 Checkpoints of errors at debugger startup (target connected) See the user's manuals of the PC7501 and emulator See MCU specifications. (3) MCU Setting Dialog Box Does Not Appear at Debugger Startup (target not connected) Table 6.3 Checkpoints of errors at debugger startup (target not connected) Table 6.4 Checkpoints of errors at debugger startup (target connected) (4) Errors Occur at Debugger Startup (target connected) See the user's manuals of the PC7501 and emulator Page Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions 7.4 How to Request for Repair Note on Transporting the Product: