Manuals / Brands / Computer Equipment / Network Card / Renesas / Computer Equipment / Network Card

Renesas M30803T-RPD-E Note on Switch Setting:, Note on Using A-D Input Group Selection:

1 74

Download 74 pages, 713.05 Kb

( 28 / 74 )

Table 3.3 Switch settings of the M30803T-RPD-E (3/3)

Signal Switch Setting Description

Voltage JP1

M30803T-RPDM

Board

Set when using at the range of the voltage within

+4.2 to +5.5 V.

Set when using at the range of the voltage within

+2.7 to +4.2 V.

IMPORTANT

Note on Switch Setting:

•Switch settings of RDY*/HOLD*, CNVss and BYTE are provided to enable

debugging without connecting to the target system. When using the emulator

debugger in connection with the target system, set SW4 to the OPEN position and

SW5 and SW6 to the center position.

Note on Using A-D Input Group Selection:

•It is necessary to set the direction register of port P10 to input. Port P10 corresponds

to the pin that performs A-D conversion.

Example: To select A-D input for P00-P07, set the direction registers of P100-P107

and P00-P07 to input. Also, when the port P0 group and port P2 group are

selected for A-D input, port P10 cannot be used as an I/O port.

Contents

Main ( 2 / 74 ) Preface To use the product properly Precautions for Safety When using outside Japan Contents Page Page Chapter 1. Precautions for Safety Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION Note on Malfunctions in the PC4701 System: WARNING Warning for Installation: Warnings for Use Environment: Caution to Be Taken for Modifying This Product: Cautions to Be Taken for Handling This Product: Notes on Downloading Firmware: Notes on Target System: Note on RESET* Input: Note on When the Emulator Debugger Ends: Note on Final Evaluation: Note on RDY* Input: Note on HOLD* Input: Note on NMI* Input: Notes on Interruption: Note on Clock Supply to the MCU: Page Notes on EMEM Dialog: Note on S/W Break: Notes on Watchdog Function: Note on Differences between Actual MCU and Emulator: Notes on A-D Input Selection Function: Note on DMA Transfer: Note on Address Match Interrupt: Note on Protect Resistor: Page Page Chapter 2. Preparation 2.1 Terminology 2.2 Package Components 2.3 Other Tool Products Required for Development 2.4 Name of Each Part (1) System Configuration (2) Inside of Emulation Pod 2.5 When Using the Emulator for the First Time Page Chapter 3. Setting Up 3.1 Removing the Upper Cover When Removing the Upper Cover: Page Table 3.1 Switch settings of the M30803T-RPD-E (1/3) Table 3.2 Switch settings of the M30803T-RPD-E (2/3) Note on Switch Setting: Note on Using A-D Input Group Selection: 3.3 Selecting Clock Supply Notes on Changing the Clock Supply: (1) Using the Oscillator Circuit on the Target System Notes on External Clock: Page (3) Replacing the Oscillator Circuit Boards 3.4 A-D Conversion Bypass Capacitor Note on the A-D Converter: 3.5 Connecting the PC4701 and Emulation Pod (1) Connecting the Cable to the PC4701 Note on Connecting the Cable: Note on Securing the Screws: Page Page (1) Connecting 100-pin LCC Socket (2) Connecting 100-pin 0.65-mm-pitch Foot Pattern (Part 1) (3) Connecting 100-pin 0.65-mm-pitch Foot Pattern (Part 2) (4) Connecting 100-pin 0.65-mm-pitch Foot Pattern (Part 3) (5) Connecting 100-pin 0.5-mm-pitch Foot Pattern (Part 1) (6) Connecting 100-pin 0.5-mm-pitch Foot Pattern (Part 2) (7) Connecting 144-pin 0.5-mm-pitch Foot Pattern Page Page Chapter 4. Usage 4.1 Turning On the Power Supply (1) Checking the Connection of the System (2) Turning On the Power Supply Notes on Power Supply: Note on Memory Expansion Mode and Microprocessor Mode: Note on CLOCK LED: 4.2 Downloading Firmware (1) When It is Necessary to Download Firmware (2) Downloading Firmware in Maintenance Mode Note on Downloading Firmware: 4.3 Starting Up the Emulator Debugger (Setting EMEM Dialog) (1) Setting the Debug Monitor Bank Address Notes on Setting Debug Monitor Bank Address: (2) Selecting the Processor Mode Notes on Selecting the Processor Mode: (3) Setting the Emulation Memory (4) Emulation Memory Allocation as Expansion Area Notes on Using Emulation Memory for Expansion: (5) Referring MCU STATUS Notes on MCU STATUS: Note on Memory Access: 4.4 Self-check (1) Self-check Procedure (2) If an Error is Detected in the Self-check Note on Self-check: Page Page Chapter 5. Specifications 5.1 Specifications * For M30802 and M30805, the FLX-144NSD (not included) is required. Page Page 5.3 Operation Timing in Memory Expansion Mode and Microprocessor Mode Table 5.3 Timing requirements (VCC = 3 V) (1) Timing Requirements Tables 5.2 and 5.3 list the timing requirements. Table 5.2 Timing requirements (VCC = 5 V) 5.4 Electrical Characteristics Page Page Page Chapter 6. Troubleshooting ( 64 / 74 ) Chapter 6. Troubleshooting 6.1 Flowchart to Remedy the Troubles Figure 6.1 Flowchart to remedy the troubles 6.2 When the Emulator Debugger Does Not Start Up Properly (1) When the LED Display of PC4701 is Abnormal Table 6.1 LED's abnormal display and its checkpoints See the instruction manual of the PC4701. See "3.5 Connecting the PC4701 and Emulation Pod" (page 34). Table 6.2 Checkpoints of errors when starting up the emulator debugger (target is connected) Table 6.3 Checkpoints of errors when starting up the emulator debugger (target is not connected) Table 6.4 Checkpoints of errors when starting up the emulator debugger (target is connected) 6.3 Operation Differs from That of Actual MCUs (1) When the A-D Conversion Values are Different from Expected Values (4) Errors Occur When the Emulator Debugger Starts Up (When the target system is connected) Page Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions 7.4 How to Request for Repair Note on Transporting the Product: