Manuals
/
Brands
/
Computer Equipment
/
Switch
/
Renesas
/
Computer Equipment
/
Switch
Renesas
M30830T-EPB user manual
1
1
72
72
Download
72 pages, 929.52 Kb
M30830T-EPB
Emulation Pod for M32C/81, 82 and 83 Groups
User's Manual
Rev.
2
.00
July 1, 2004
REJ10J0747-0
2
00Z
Contents
Main
( 2 / 72 )
To use the product properly
Precautions for Safety:
Preface
Contents
Page
Page
Chapter 1. Precautions for Safety
Page
Chapter 1. Precautions for Safety
WARNING IMPORTANT
CAUTION
WARNING
Page
Note on NMI* Input:
Notes on Interruption:
Note on Clock Supply to the MCU:
Notes on Access Prohibited Area:
Notes on Stack Area:
Notes on EMEM Dialog Box:
Notes on Reset Vector Area:
Note on S/W Break:
Note on Differences between Actual MCU and Emulator:
Notes on Watchdog Function:
Note on Protect Resistor:
Notes on A-D Input Selection Function:
Note on DMAC II Transfer Completion Interrupts:
Note on DMA Transfer:
Page
Page
Chapter 2. Preparation
2.1 Terminology
2.2 Package Components
2.3 Other Tool Products Required for Development
2.4 Name of Each Part
(1) System Configuration
(2) Names and Functions of PC7501 Upper Panel LEDs
Caution for Target Status POWER LED:
2.5 When Using the Emulator for the First Time
Chapter 3. Setting Up
Page
3.2 Selecting Clock Supply
Notes on Changing the Clock Supply:
(1) Using the Oscillator Circuit on the Target System
Notes on External Clock:
Page
(3) Replacing the Oscillator Circuit Boards
Page
Table 3.2 Switch settings of the M30830T-EPBM (1/2)
Table 3.3 Switch settings of the M30830T-EPBM (2/2)
3.4 A-D Conversion Bypass Capacitor
Note on the A-D Converter:
3.5 Connecting the PC7501
Note on Connecting the Cable:
Page
(1) Connecting 100-pin LCC Socket
(2) Connecting 100-pin 0.65-mm-pitch Foot Pattern (Part 1)
(3) Connecting 100-pin 0.65-mm-pitch Foot Pattern (Part 2)
(4) Connecting 100-pin 0.65-mm-pitch Foot Pattern (Part 3)
(5) Connecting 100-pin 0.5-mm-pitch Foot Pattern (Part 1)
(6) Connecting 100-pin 0.5-mm-pitch Foot Pattern (Part 2)
(7) Connecting 100-pin 0.5-mm-pitch Foot Pattern (Part 3)
(8) Connecting 144-pin 0.5-mm-pitch Foot Pattern
Page
Chapter 4. Usage
4.1 Turning On the Power
(1) Checking the Connection of the Emulator System
(2) Turning ON/OFF the Power
Notes on Power Supply:
Note on Memory Expansion and Microprocessor Modes:
Note on CLOCK LED:
TARGET
SYSTEM
4.2 Downloading Firmware
Note on Downloading Firmware:
4.3 Starting Up the Emulator Debugger (Setting EMEM Dialog Box)
(1) Setting the Debug Monitor Bank Address
Notes on Setting Debug Monitor Bank Address:
(2) Selecting the Processor Mode
Notes on Selecting the Processor Mode:
(3) Setting the Emulation Memory
(4) Emulation Memory Allocation as Expansion Area
Notes on Using Emulation Memory for Expansion:
Note on Memory Access:
(5) Referring MCU STATUS
Notes on MCU STATUS:
4.4 Self-checks
(1) Self-check Procedure
(2) If an Error is Detected in Self-checks
Note on Self-checks:
Figure 4.4 Self-check procedure
( 52 / 72 )
Page
Chapter 5. Specifications
5.1 Specifications
Table 5.1 lists the specifications of the M30830T-EPB. Table 5.1 Specifications of the M30830T-EPB
Page
Figure 5.2 Connection diagram (2/2) Table 5.2 Electrical characteristics of the 74HC4066
Page
Page
Page
Page
Chapter 6. Troubleshooting
( 62 / 72 )
Chapter 6. Troubleshooting
6.1 Flowchart to Remedy the Troubles
Figure 6.1 Flowchart to remedy the troubles
6.2 When the Emulator Debugger Does Not Start Up Properly
(1) When the LED Display of the PC7501 is Abnormal
Table 6.1 LED's abnormal display and its checkpoints
See the user's manual of the PC7501.
See "3.5 Connecting the PC7501" (page 33).
Table 6.2 Checkpoints of errors when starting up the emulator debugger (target is connected)
Table 6.3 Checkpoints of errors when starting up the emulator debugger (target is not connected)
(4) Errors Occur When the Emulator Debugger Starts Up (When the target system is connected)
Table 6.4 Checkpoints of errors when starting up the emulator debugger (target is connected)
Page
Page
Chapter 7. Maintenance and Guarantee
7.1 Maintenance
7.2 Guarantee
7.3 Repair Provisions
7.4 How to Request for Repair
Note on Transporting the Product: