Renesas M37641T2-RPD-E (2)Inside of the Emulation Pod

( 21 / 68 )

(2)Inside of the Emulation Pod

Figure 2.2 Internal view of the emulation pod

(1) Base board

Base board for the 740 Family MCUs which controls the interface with the PC4701 and the

evaluation MCU.

(2) Memory board

Board on which the 128 KB emulation memory is mounted.

(3) Oscillator circuit board

Board on which the oscillator circuit in the emulation pod is mounted. Its operating frequency can

be changed by replacing this board with other available oscillator circuit boards.

(4) MCU-dependent board

Board grouping parts (number of pins or added functions) which vary according to MCU model.

(5) Evaluation MCU

Microcomputer (dedicated to the emulator) operated in the specific mode for the emulator. It is

necessary to replace the evaluation MCU according to the MCU you use.

Contents

Main Page Preface To use the product properly Precautions for Safety: When using outside Japan Contents Page Page Page Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION WARNING Warning for Installation: Warnings for Use Environment: Caution to Be Taken for Modifying This Product: Cautions to Be Taken for Handling This Product: Notes on Downloading Firmware: Note on Malfunctions in the PC4701 System: Note for PC4700 System: Note on Map Settings (MAP Command): Page Note on Differences between the Actual MCU and Emulator: Page Note on Reading MCU Internal Resources: Note on a Watch Point: Note on Event Breaks: Note on Software Breaks: Page Page Page Chapter 2. Preparation 2.1 Terminology 2.2 Package Components 2.3 Other Tool Products Required for Development 2.4 Name of Each Part (1)System Configuration (2)Inside of the Emulation Pod 2.5 Using the Emulator for the First Time Page Chapter 3. Setting Up 3.1 Removing the Upper Cover When Removing the Upper Cover: 3.2 Replacing the Evaluation MCU Page Table 3.1 Switch settings of the M37641T2-RPD-E 3.4 Connecting USB-related Signals (1)Pins D+ and D- Notes on the USB Connector: (2)Pin Ext. Cap 3.5 Selecting Clock Supply Note on Changing Clock Supply: (3)Pins LPF, AVss and AVcc Note on Connecting USB-related Pins: (1)Using the Oscillator Circuit on the Target System Notes on the External Clock: Page (3)Replacing the Oscillator Circuit Boards 3.6 Connecting the PC4701 and Emulation Pod (1)Connecting the Cable to the PC4701 Notes on Connecting the Cable: Note on Securing the Screws: Page Notes on Connecting the Target System: 3.7 Connecting the Target System Page Chapter 4. Usage 4.1 Turning On the Power (1)Checking the Connections of the Emulator System (2)Turning On the Power Notes on Power Supply: (3) LED Display When the PC4701 Starts Up Normally 4.2 Downloading Firmware (1)When It is Necessary to Download Firmware (2)Downloading Firmware in Maintenance Mode Note on Downloading Firmware: 4.3 Starting Up Emulator Debugger (Init Dialog Box Settings) (1) Settings in the CLOCK Tab 4.4 Self-check (1)Self-check Procedure (2)If an Error is Detected in the Self-check Note on the Self-check: (2) Settings in the MCU Tab Page Page Page Chapter 5. Specifications 5.1 Specifications 5.2 Connection Diagrams Page 5.3 Operation Timing (1) Operation Timing When Using the Evaluation MCU (M37641M8-XXXFS) Table 5.2 Timing requirements and switching characteristics (Vcc = 5.0V, = 12 MHz) Table 5.3 Timing requirements and switching characteristics (Vcc = 3.0 V, = 6 MHz) (2) Operation Timing When Using the Evaluation MCU (M37643M8-XXXFS) Table 5.4 Timing requirements and switching characteristics (Vcc = 5.0V, = 12 MHz) Table 5.5 Timing requirements and switching characteristics (Vcc = 3.0 V, = 6 MHz) Page Page Page Page Page Chapter 6. Troubleshooting 6.1 Flowchart to Remedy Troubles Figure 6.1 Troubleshooting when starting up the emulator system (1)When the LED Display of the PC4701 is Abnormal Table 6.1 LED's abnormal display and checkpoints (2)When the Init Dialog Box is Not Displayed See the user's manual of the PC4701. See "3.6 Connecting the PC4701 and Emulation Pod" (page 34). (3)When the Program Window is Not Displayed (Target System Not Connected) Table 6.2 Checkpoints of errors when starting up the emulator debugger (target system not connected) (4)When the Program Window is Not Displayed (Target System Connected) Table 6.3 Checkpoints of errors when starting up the emulator debugger (target system connected) 6.2 When the M37641T2-RPD-E Does Not Work Properly Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions 7.4 How to Request for Repair Note on Transporting the Product: