Manuals / Brands / Computer Equipment / Switch / Renesas / Computer Equipment / Switch

Renesas M37760T-RPD-E Notes on Emulation Memory Settings:

1 64

Download 64 pages, 1.52 Mb

( 38 / 64 )

CAUTION

Notes on Emulation Memory Settings:

• Set the SFR area (00000016 - 0001FF16) to EXTERNAL.

• Set internal RAM area (00100016 - 001BFF16) to INTERNAL.

Choose the "M37760mf.mcu" file for

M37760 Group MCUs.

4.4 Starting Up Emulator Debugger - Part 2 (Setting EMEM Dialog)

The EMEM dialog box will appear after the settings in the Init dialog box by starting up the emulator

debugger or downloading the firmware. Here explains how to set the processor mode of the target

MCU, allocate the emulation memory and set the debug monitor area. The dialog box shown below

is an example of the emulator debugger M3T-PD77 V.4.00 Release 1. The display and setup items

may vary according to the version of the M3T-PD77. For more details, refer to M3T-PD77 User's

Manual.

Figure 4.4 Emem dialog display

(1) Setting Processor Mode Tab

Be sure to use single-chip mode as a processor mode.

(2) Setting MAP Tab

Debug Monitor tab

MAP tab

It is not necessary to set these tabs for this product.

Processor tab

Contents

Main Page Preface To use the product properly Precautions for Safety: When using outside Japan Terminology Contents Page Page Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION WARNING Warning for Installation: Warnings for Use Environment: Caution to Be Taken for Modifying This Product: Cautions to Be Taken for Handling This Product: Page Note on Malfunctions in the PC4701 System: Notes on Downloading Firmware: Note for PC4700 System: Note on Processor Mode Register (address D8 Notes on Target System: Note on ROM Correction Function: Note on Watchdog Function: Note on Differences between Actual MCU and Emulator: Note on Software Breaks: Note on Monitor Work Area of the Emulator: Note on Watch Point: Note on Event Breaks: Note on Reading Out the MCU Internal Resources: Chapter 2. Preparation 2.2 Other Tool Products Required for Development Chapter 2. Preparation 2.1 Package Components 2.3 Name of Each Part (1) System Configuration (2) Inside of the Emulation Pod 2.4 When Using the Emulator for the First Time Page Page Chapter 3. Setting Up 3.1 Removing the Upper Cover When Removing the Upper Cover: Page Table 3.1 Switch settings of the M37760T-RPD-E 3.3 Selecting Clock Supply Note on Changing the Clock Supply: (1) Using the Oscillator Circuit on the Target System Notes on Operating with the External Clock: Page (3) Replacing the Oscillator Circuit Boards 3.4 Connecting the PC4701 (1) Connecting the Cable to the PC4701 Note on Connecting the Cable: Note on Securing the Screws: Page Notes on Connecting the Target System: 3.5 Connecting the Target System Page Page Chapter 4. Usage 4.1 Turning On the Power Supply (1) Checking the Connection of the System (2) Turning On the Power Supply Notes on Power Supply: Note on Downloading Firmware: 4.3 Starting Up Emulator Debugger - Part 1 (Setting INIT Dialog) (1) Setting MCU Tab (2) Setting CLOCK Tab Note on Setting XCIN Pin: Notes on Emulation Memory Settings: 4.4 Starting Up Emulator Debugger - Part 2 (Setting EMEM Dialog) (2) Setting MAP Tab (1) Setting Processor Mode Tab (3) Setting Debug Monitor Tab Note on Monitor Work Area: Note on Debug Bank Memory Area: Note on Watchdog Timer: 4.5 Self-check (1) Self-check Procedure Note on the Self-check: Page Page Page Chapter 5. Specifications 5.1 Specifications Table 5.1 lists the specifications of the M37760T-RPD-E. Table 5.1 M37760T-RPD-E specifications Page Page Page Page Page Page Page Page Page ( 54 / 64 ) Chapter 6. Troubleshooting When this product does not work properly, check the following. Figure 6.1 Troubleshooting when the emulator debugger starts up 6.1 Troubleshooting up to Emulator Debugger Startup (1) Errors Displayed over the Emem Dialog Box and Remedial Action 6.2 When the M37760T-RPD-E Does Not Work Properly 6.3 How to Request for Support Page Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions 7.4 How to Request for Repair Note on Transporting the Product: