RF-RBKIT Wireless HD Audio Starter Kit

Package contents:

TM

Wireless sender

 

 

 

 

 

 

 

TM

 

 

 

 

3.5 mm female-to-RCA

 

IR remoteDC adapter

AC power cable

 

User Guide Speaker cable,

3.5 mm male-to-male

stereo cable,

Cable spool
Quick Setup Guide

6 in. (x2)

Wireless receiver(for sender)(for receiver)

 

3 ft (x4)

stereo cable, 3ft (x2)

 

(for receiver)

Please Read First

Every Rocketboost network must contain at least one hub device, which directs network data tra￿c and helps devices join the network. The network can have only one hub, which can be enabled by using the hub switch on the back of all Rocketboost transmitters. The sender in this kit is set at the factory for hub mode and the receiver has been pre-joined to this sender at the factory for easy setup. If you have an existing Rocketboost network, the sender's hub mode switch should

be set to Disable. The sender and receiver also need to be joined to your existing hub device (the one with the green power LED).

See your User Guide for instructions on joining devices to the network.

Sender

TM

TM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11

 

 

12

13

14

 

 

15

 

 

 

 

 

 

16

 

 

 

 

 

1

Standby LED

 

 

9

HD B button

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

Power/Join button

 

 

 

10 HD B indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

Power/Join indicator

11

DC IN jack

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

HD A indicator

 

 

12

SPEAKER IN A jacks

 

 

 

 

 

 

 

 

5

HD A button

 

 

13

Pre-in A/B jack

 

 

 

 

 

 

 

 

6

Source A button

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 1 Preparing the remote control

To activate the battery: Removethetabfromthebottomofthe remotecontroltoenablethebattery.

Step 2 Connecting the sender

Connecting to an ampli￿er

(surround mode is described below, as an example) Connect the right surround speaker terminals of your ampli￿er to the right speaker terminals of the sender by connecting the red speaker wire to the red (+) terminals, and the black speaker wire to the black (-) terminals. Repeat to connect the left surround speaker terminals.

Connecting to an external audio source

(such as an MP3 player)

Connect external audio source(s) to the Pre-in A and/or B jacks

on the rear of sender using the 3.5 mm male-to-male stereo

cable and the 3.5 mm female-to -RCA stereo cable.

Note: The Input A/Input B buttons on the remote control allow

you to select between the Speaker in or Pre in (line level). Each

press of the button will toggle to the other source. The unit

must be powered up for these buttons to operate and the

state when powered down will be remembered.

Step 3 Connecting the receiver

 

 

 

 

7

Source A/B LED indicator

15

SPEAKER IN B jacks

 

 

 

 

Hub Enable switch

1 2 3

4 5

6 7 8

9 10

8

Source B button

16

4 -Channel Lock switch

Receiver

9

 

10

SPEAKER-OUT (4-8 Ohm)

 

 

 

 

TM

 

AC IN

 

TM

 

 

120V~,60Hz

 

 

 

 

R

L

SPEAKER-OUT (4-8 Ohm)

AC IN 120V~,60Hz

R L

Connect the right surround speaker to the right speaker terminals on the receiver. Use a red speaker wire to connect the red (+) terminals and a

black speaker wire to connect the

black (-) terminals.

Repeat this step to connect the left surround speaker.

 

 

 

 

 

 

 

 

 

11

12

13

14

 

 

 

 

 

 

 

 

1

Standby LED

 

9 IR sensor

 

 

 

 

 

 

 

 

 

2

Power/Join button

10 VOLUME knob

 

 

 

 

 

 

 

 

 

3

Power/Join indicator

11 Removable cable spool slot

 

 

 

 

 

 

 

 

4

BASS button

 

12 AC IN jack

 

 

 

 

 

 

 

 

 

5

Bass indicator

 

13 Removable cable spool slot (line level)

 

 

 

 

 

 

 

 

6

SOURCE indicator

14 SPEAKER OUT jacks

 

 

 

 

 

 

 

 

7

SOURCE button

 

 

 

1

2

3

4

5

6

7

8

8

HD indicator

 

 

 

 

 

 

 

 

Step 4 Establishing communication

The sender and receiver packaged together were pre-joined at the factory, so if you are only using one sender and receiver set, no further con￿guration is needed. If an active link is established between them, the Power/Join indicators on both units will light steadily (no blink). If your sender and receiver are

not correctly linked (the power LEDs will ￿ash slowly) or you need to add additional Rocketboost products, see your User Guide for more information. Make sure the Source A or B LED is illuminated on the sender for the channel that you have connected to your network for the audio transmission to be active.

Press the SOURCE button on the receiver until the audio channel you desire is playing. Adjust the volume as desired.

09-0474

QUICK SETUP GUIDE