QUICK SETUP GUIDE
RF-TVMLPT03
Thank you for choosing the Rocketfish
a TV weighing up to 130 lbs. (59 kg)
1 Attach the TV brackets Option 1: Attaching to a at mounting surface
Attach the left and right TV brackets (B and C) to the back of the TV using: The M4/M5 washers (F) and
the M4 x 12 mm (D)
or M5 x 12 mm (H) screws. Or
The M6/M8 washers (M) and the M6 x 12 mm (J) screws or M6 x 20 mm (K) screws
or the M8 x 16 mm (O) screws.
C
B | F or M |
or |
2 Install the wall plate
Option 1: Installing to a wood stud wall
Caution: Avoid potential injuries or property damage! DO NOT
Note: Any material covering the wall must not exceed 5/8 in. (16 mm).
a.Locate the studs. Verify the center of the stud with an awl or thin nail or use an
b.Level the wall plate (A) and mark hole locations.
c.Drill pilot holes as illustrated.
d.Align the wall plate (A) with the pilot holes, then place the washers (T) over the holes. Insert the lag bolts (U) through the washers, then tighten the lag bolts with a socket wrench only until the washers are pulled firmly against the wall plate.
DO NOT
a. |
Package contents
AWall plate (1)
BLeft TV bracket (1)
CRight TV bracket (1)
M4 bagDM4 x 12 mm screws (4)
EM4 x 30 mm screws (4)
FM4/M5 washers (8)
GM4/M5 spacers (4)
B
A
C
B 
C | D H |
| |
| J K |
| O |
< 16 mm |
|
|
|
| |
|
|
|
| ||
(5⁄8 in.) |
|
|
|
| |
16 | - | 24 in. | |||
| |||||
|
| 406mm | - | ||
b. |
|
|
| 610mm | |
|
|
|
| ||
HM5 x 12 mm screws (4)
IM5 x 30 mm screws (4)
M6 bagJM6 x 12 mm screws (4)
KM6 x 20 mm screws (4)
LM6 x 35 mm screws (4)
MM6/M8 washers (4)
NM6/M8 spacers (4)
M8 bagOM8 x 16 mm screws (4)
PM8 x 40 mm screws (4)
QM8 x 60 mm screws (4)
Hex key bagR3⁄16 in. Hex Key (1)
M4 bag | D |
| |
M4 x 12mm | |
M5 bag | H |
| |
M5 x 12mm | |
M6 bag | J |
| |
M6 x 12mm | |
| E | F | G |
M4 x 30mm |
|
|
|
|
| M4/M5 | M4/M5 |
|
|
| |
| I |
|
|
M5 x 30mm |
|
|
|
K |
| L | M |
M6 x 20mm | M6 x 35mm | M6/M8 |
|
|
| M6/M8 |
N
Option 2: Attaching to a curved or | A |
irregular mounting surface | c. |
Attach the left and right TV brackets (B and C) to the | |
back of the TV using: |
|
The M4/M5 spacers (G), M4/M5 washers (F), and | C |
the M4 x 30 mm screws (E) or M5 x 30 mm screws (I). Or
The M6/M8 spacers (N), M6/M8 washers (M),
and the M6 x 35 mm screws (L) |
| d. | |
or the M8 x 40 mm (P) or M8 x 60 mm screws(Q). |
|
| |
| |||
|
|
| |
Note: Use the M4 washers (F) between |
|
|
|
|
| ||
|
| ||
the spacers and the bracket with the M4 |
|
| |
or M5 screws only. |
|
| |
75mm 3 in.
| Lag bolt bag | M8 bag | O |
| ||
S Concrete anchors (4) |
|
|
T Lag bolt washers (4) |
| M8 x 16mm |
U 5⁄16 in. x 23⁄4 in. lag bolts (4) |
| |
P | Q |
M8 x 40mm | M8 x 60mm |
Hex key bag
R
3/16 in.
B | F or |
|
|
|
|
F | M |
|
|
| |
|
|
|
|
| |
|
| E | I | U | T |
|
|
| |||
|
| L | P |
|
|
| Tools you will need: | • Phillips screw driver | Lag bolt bag | S |
| • Stud finder | • Hammer (Concrete Only) |
|
|
| • Awl | • ½ in. socket wrench |
|
|
| • Pencil |
|
| |
| • 3/16 in. wood drill bit |
|
| |
| • Level |
|
| |
• 3/8 in. masonry drill bit (Concrete Only) |
|
| |
| • Tape measure |
|
| |
| • Power drill |
|
| |
|
|
|
T
U
in. x 2 in.
| G or N | Q |
|
B 
C