19

Appendix

Español Português NederlandsItalianoFrançaisDeutschEnglish
CONTROL PEDAL
MASTER

These parameters are applied to the entire VE-20.

SETUP
FACTORY RESET

Power doesn’t come on

QHave the batteries run down?
→Replace them with new batteries (p. 3).
* The batteries included with the VE-20 are meant only to confirm that
the unit is functional at the factory.
QIs the specified AC adaptor (PSA series; optional)
connected correctly?
→Check the connections again (p. 7).
Never use any AC adaptor other than the adaptor
specified.
QCould the POWER switch be OFF?
→Turn the POWER switch ON (p. 4).

No sound/volume is low

QIs the other equipment connected correctly?
→Check the connections again (p. 7).
QCould the volume or input gain of the connected
mixer or recorder be lowered?
→Check the settings of the conne cted devic e.
QCould the Phantom Power parameter be set to Off?
→
If you’re using a condenser mic that requires phantom
power, set the Phantom Power parameter to the On (p. 16).
QCould the MicSens or Volume settings be too low?
→Adjust these to appropriate values (p. 4).
QHave the batteries run down?
→Replace them with new batteries (p. 3).
* The batteries included with the VE-20 are meant only to confirm that
the unit is functional at the factory.

The POWER indicator has gone dim

QIs the specified adaptor (PSA series; optional)
properly connected?
→Check the connection once more (p. 7).
* Never use any AC adaptor oth er than one specified for use with the
VE-20.
QHave the batteries run down?
→Replace them with new batteries (p. 3).
* When the indicator goes dim or no longer lights whil e the effect is on,
it means that the batteries must be replaced.
* The batteries included with the VE-20 are meant only to confirm that
the unit is functional at the factory.

Sound is distorted

QIs the MicSens setting appropri ate?
→Adjust the setting a ppropriately (p. 4).
QIs the output from another effects processor
connected to the INPUT jack?
→Connect your mic directly to the INPUT jack.

Can’t store the recorded phrase

→
It is not possible to store a recorded ph rase in the VE-20.

Can’t overdub using Phrase Loop

QCould the Phrase Loop parameter be set to Check?
→Overdubbing is not possible if this is set to Check.
If you want to overdu b, set the P hrase Loop pa rameter
to Perform (p. 15).
Parameter Explanation
Type DBL/HRM
Switches each effect on/off (p. 14).
DELAY
PITCH
TONE/SFX
REVERB
DYNAMICS
CUSTOM Turns the specified effect on/off (p. 14).
Parameter Explanation
Level Specifies the volume of the sound.
NoiseThres Adjust this according to the noise level.
Set this to a larger value if the noise level is high, or
to a lower value if the noise level is low.
Key
Specifies the key of the song you’re singing (p. 11).

System parameters

Parameter Explanation
MicSens Adjusts the input sensitivity.
PhantomPow-
er On, Off Turns on/off the supply of phantom
power to the INPUT jack.
Output Mono Mono output from OUTPUT connec-
tors L (MONO) and R.
Stereo Stereo output from the OUTPUT c on-
nectors.
Mono/Dry
Mono output from OUTPUT connec-
tor L (MONO) and Dry sound from
connector R.
* This setting also applies to the L and
R signals of the PHONES/LINE jack.
LowCut On, Off Cuts unwanted low-frequency con-
tent.
LoopType
Perform
Select this if you want to use the
Phrase Loop function to overdub (p.
13).
Check Select this if you want to perform a
sound check (p. 15).
Contrast Adjusts the display contrast (legibility).
Parameter Explanation
ALL All settings will be initialized.
SOUND All user sound settings will be initialized.
SETUP Setup parameter settings will be initialized.
Troubleshooting
VE-20_e.book 19 ページ ２００９年７月３０日　木曜日　午後８時１３分