Rolls MA2355 INTRODUCTION, INSPECTION, CONNECTION, DESCRIPTION FRONT PANEL, REAR PANEL, OPERATION

INTRODUCTION

Thank your for your purchase of the Rolls MA2355 Mixer / Amplifier. The MA2355 is a

single rack space mixer amplifier designed for restaurants, schools, churches, clubs etc.

The unit provides a compact and efficient way to mix up to three sources such as AM/FM

tuners, CD players, and video players with up to two microphones. Priority talkover is pro-

vided on Microphone Two for paging, and on Source One for a jukebox, telephone, etc.

INSPECTION

1. Unpack and inspect the MA2355 box and package.

If obvious physical damage is noticed, contact the carrier immediately to make a damage

claim. We suggest saving the shipping carton and packing materials for safely transporting

the unit in the future.

2. For warranty information, and to register your MA2355 warranty, please visit our web-

site at

www.rolls.com

and click on the Register Your Warranty Here button

DESCRIPTION

FRONT PANEL

Treble

: Adjusts the high frequencies of the Source 2 and 3 signals only.

Bass

: Adjusts the low frequencies of the Source 2 and 3 signals only.

IN 1:

1/8” (3.5mm) Tip-Ring-Sleeve input jack - parallels the rear-panel Source Input 1.

Source 1 - 3

: Adjust the volume of input from the RCA Source Inputs.

Mic 1, 2

: Adjust the level of signal from the corresponding Mic Input.

TONE 1, 2

: Adjusts the frequency content of the microphone signal in the channel. When

the control is turned counter-clockwise, the high frequencies are cut, when the control is

turned clockwise, the low frequencies are cut.

Right/Left Output Levels

: Adjusts the output level of the MA2355 amplifier.

Power

: LED indicating power is applied to the MA2355 and the unit is on.

Clip

. LED indicating overload in the MA2355 amplifier.

REAR PANEL

120 VAC 50/60 HZ 15 VA

: IEC Power Cord. Connect to a properly grounded AC source.

NOTE: REPLACE THE FUSE WITH ONLY THE PROPER RATED FUSE. INSTALLING A

FUSE OTHER THAN THE RECOMMENDED RATING WILL DAMAGE THE UNIT.

LEFT/RIGHT OUTPUTS

: Spring-loaded terminal for connection to the speakers.

POWER AMP INSERTS

: 1/4” Tip-Send, Ring-Return insert jack.

MICROPHONE ONE and TWO

: Balanced XLR inputs to be connected to dynamic or

condenser microphones.

DIP SWITCH

: Contains the small switches for engaging Mic 1, 2 phantom power, and the

priority (Talk Over) functions.

SOURCE INPUTS

: Stereo RCA jacks, Channels 1 - 3, for connection to stereo sources

such as AM/FM tuners, cassette players, cd players, or a jukebox.

RECORD OUT

: Stereo RCA jacks, contains all mixed signals before the Master Level

RECORD OUT: Stereo RCA jacks, contains all mixed signals before the Master Level RECORD OUT

control.

CONNECTION

Inputs

Connect low impedance microphones to the Mic inputs. If a paging microphone is being

used, connect it to Mic Input 2 so it may be used with the Talk Over function. Connect

source signals such as CD players, cassette players or video players to the RCA Source

Inputs. If a jukebox is being connected, and you want its signal to mute the other source

signals, connect it to Source input 1.

For recording purposes, connect a stereo RCA cable to the Record Out jacks, and to your

recording device.

Amp Insert

To connect a signal processor to the

MA1705 signal, use an insert plug,

or cable wired as shown in Fig. 1.

This return signal is then sent to the

output level section of the amplifier.

Outputs

Connect speakers (use impedances no lower than 8 ohms) to the Outputs of the MA2355

by pressing in each of the spring-loaded terminals and inserting the proper wire into the

proper terminal i.e.; + = red, - = black.

To Amp Insert

OPERATION

DIP SWITCH SETTINGS

(From left to right)

• If a microphone requires phantom power, move the Mic channel’s

corresponding PHANTOM POWER switch to the up position. This ap-

plies 12 volts dc phantom power to the indicated microphone.

• Mic 2 Priority; when in the up position, all program material on Mic 1

and Sources 2 and 3 will be “ducked” or muted when a signal is pres-

ent at Mic 2. Source 1 is left un-muted.

This function is used for paging.

• Source 1 Priority: when in the up position, Source 2,and 3 will be

“ducked” or muted by the signals at Source 1.

This function is for jukebox priority. With a jukebox connected to Source input 1, and the

Talkover switch 2 on, the other Source input signals such as background music, will be

muted and only the jukebox will be heard.

FAULT PROTECTION

The fault protection in the MA2355 limits the current to the output stage. This mode is en-

tered whenever the output stage is called upon for too much power, it may also be fooled

by impedances lower than four ohms - which may cause the output stage to overheat and

be irreversably damaged.

BURN WARNING!

THE FRONT PANEL OF THE MA2355 IS THE HEAT DISTRIBUTION FOR THE OUT-

PUT STAGE. IF THE UNIT IS OPERATED AT HIGH VOLUMES, IT MAY GET HOT.

SOURCE 1

MIC 2

PHANTOM

POWER

PRIORITY ◗

2 1

not used